Niveo NGSME48T4H Скачать руководство пользователя страница 57

Страница: 57 / 338

Chapter

3: Web Management

Security - Switch - SNMP - System

PoE Switch User Manual | 57

Engine ID

Indicates the SNMPv3 engine ID. The string must contain an even number(in hexadecimal

format) with number of digits between 10 and 64, but all-zeros and all-'F's are not allowed.

Change of the Engine ID will clear all original local users.

SNMP Trap Configuration

Configure SNMP trap on this page.

Trap Mode

Indicates the SNMP trap mode operation. Possible modes are:



Enabled:

Enable SNMP trap mode operation.



Disabled:

Disable SNMP trap mode operation.

Trap Version

Indicates the SNMP trap supported version. Possible versions are:



SNMP v1:

Set SNMP trap supported version 1.



SNMP v2c:

Set SNMP trap supported version 2c.



SNMP v3:

Set SNMP trap supported version 3.

Trap Community

Indicates the community access string when sending SNMP trap packet. The allowed

string length is 0 to 255, and the allowed content is ASCII characters from 33 to 126.

Trap Destination Address

Indicates the SNMP trap destination address. It allow a valid IP address in dotted decimal

notation ('x.y.z.w').

And it also allow a valid hostname. A valid hostname is a string drawn from the alphabet

(A-Za-z), digits (0-9), dot (.), dash (-). Spaces are not allowed, the first character must be

an alpha character, and the first and last characters must not be a dot or a dash.

Содержание NGSME48T4H



















































































































































































































































































































































Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды

Niveo NGSME48T4H, Руководство пользователя

Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды