Niveo NGSME48T4H Скачать руководство пользователя страница 28

Страница: 28 / 338

Chapter

3: Web Management

Web Management - Configure

PoE Switch User Manual | 28

System accepts the valid IPv6 unicast address only, except IPv4-Compatible address and

IPv4-Mapped address.

The field may be left blank if IPv6 operation on the interface is not desired.

IPv6 Mask

The IPv6 network mask, in number of bits (prefix length). Valid values are between 1 and 128

bits for a IPv6 address.

The field may be left blank if IPv6 operation on the interface is not desired.

IP Routes

Delete

Select this option to delete an existing IP route.

Network

The destination IP network or host address of this route. Valid format is dotted decimal

notationor a valid IPv6 notation. A default route can use the value 0.0.0.0or IPv6 :: notation.

Mask Length

The destination IP network or host mask, in number of bits (prefix length). It defines how

much of a network address that must match, in order to qualify for this route. Valid values are

between 0 and 32 bits respectively 128 for IPv6 routes. Only a default route will have a mask

length of 0 (as it will match anything).

Gateway

The IP address of the IP gateway. Valid format is dotted decimal notationor a valid IPv6

notation. Gateway and Network must be of the same type.

Next Hop VLAN (Only for IPv6)

The VLAN ID (VID) of the specific IPv6 interface associated with the gateway.

The given VID ranges from 1 to 4094 and will be effective only when the corresponding IPv6

interface is valid.

If the IPv6 gateway address is link-local, it must specify the next hop VLAN for the gateway.

If the IPv6 gateway address is not link-local, system ignores the next hop VLAN for the

gateway.

Buttons



Add Interface:

Click to add a new IP interface. A maximum of 128 interfaces is

supported.



Add Route:

Click to add a new IP route. A maximum of 32 routes is supported.

Содержание NGSME48T4H



















































































































































































































































































































































Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды

Niveo NGSME48T4H, Руководство пользователя

Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды