Niveo NGSME48T4H Скачать руководство пользователя страница 107

Страница: 107 / 338

Chapter

3: Web Management

Security - Network - ARP Inspection - Static Table

PoE Switch User Manual | 107

3.1.5.13.2. Security - Network - ARP Inspection - Static Table

Delete

Check to delete the entry. It will be deleted during the next save.

Port

The logical port for the settings.

VLAN ID

The vlan id for the settings.

MAC Address

Allowed Source MAC address in ARP request packets.

IP Address

Allowed Source IP address in ARP request packets.

Buttons



Add New Entry:

Click to add a new entry to the Static IP Source Guard table.



Save:

Click to save changes.



Reset:

Click to undo any changes made locally and revert to previously saved

values.

Содержание NGSME48T4H



















































































































































































































































































































































Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды

Niveo NGSME48T4H, Руководство пользователя

Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды