Niveo NGSME48T4H Скачать руководство пользователя страница 37

Страница: 37 / 338

Chapter

3: Web Management

Green Ethernet - LED

PoE Switch User Manual | 37

Port Configuration

Port

The switch port number of the logical port.

ActiPHY

Link down power savings enabled.

ActiPHY works by lowering the power for a port when there is no link. The port is power up for

short moment in order to determine if cable is inserted.

PerfectReach

Cable length power savings enabled.

PerfectReach works by determining the cable length and lowering the power for ports with

short cables.

EEE

Controls whether EEE is enabled for this switch port.

Buttons



Save:

Click to save changes.



Reset:

Click to undo any changes made locally and revert to previously saved values.

Содержание NGSME48T4H



















































































































































































































































































































































Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды

Niveo NGSME48T4H, Руководство пользователя

Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды