Niveo NGSME48T4H Скачать руководство пользователя страница 293

Страница: 293 / 338

Chapter

3: Web Management

LLDP - EEE

PoE Switch User Manual | 293

3.2.11.4. LLDP - EEE

By using EEE power savings can be achieved at the expense of traffic latency. This latency

occurs due to that the circuits EEE turn off to save power, need time to boot up before

sending traffic over the link. This time is called "wakeup time". To achieve minimal latency,

devices can use LLDP to exchange information about their respective tx and rx "wakeup time

", as a way to agree upon the minimum wakeup time they need.

This page provides an overview of EEE information exchanged by LLDP.

LLDP Neighbors EEE Information

The displayed table contains a row for each port. The columns hold the following information:

Local Port

The port on which LLDP frames are received or transmitted.

Tx Tw

The link partner's maximum time that transmit path can hold-off sending data after

deassertion of LPI.

Rx Tw

The link partner's time that receiver would like the transmitter to hold-off to allow time for the

receiver to wake from sleep.

Fallback Receive Tw

The link partner's fallback receive Tw.

A receiving link partner may inform the transmitter of an alternate desired Tw_sys_tx. Since a

receiving link partner is likely to have discrete levels for savings, this provides the transmitter

with additional information that it may use for a more efficient allocation. Systems that do not

implement this option default the value to be the same as that of the Receive Tw_sys_tx.

Echo Tx Tw

The link partner's Echo Tx Tw value.

The respective echo values shall be defined as the local link partners reflection (echo) of the

remote link partners respective values. When a local link partner receives its echoed values

from the remote link partner it can determine whether or not the remote link partner has

received, registered and processed its most recent values. For example, if the local link

partner receives echoed parameters that do not match the values in its local MIB, then the

local link partner infers that the remote link partners request was based on stale information.

Содержание NGSME48T4H



















































































































































































































































































































































Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды

Niveo NGSME48T4H, Руководство пользователя

Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды