Niveo NGSME48T4H Скачать руководство пользователя страница 129

Страница: 129 / 338

Chapter

3: Web Management

IPMC Profile - Profile Table

PoE Switch User Manual | 129

Rule

When the profile is created, click the edit button to enter the rule setting page of the

designated profile. Summary about the designated profile will be shown by clicking the view

button. You can manage or inspect the rules of the designated profile by using the following

buttons:



Navigate:

List the rules associated with the designated profile.



Edit:

Adjust the rules associated with the designated profile.

Buttons



Add New IPMC Profile:

Click to add new IPMC profile. Specify the name and

configure the new entry. Click "Save".



Save:

Click to save changes.



Reset:

Click to undo any changes made locally and revert to previously saved values.

Содержание NGSME48T4H



















































































































































































































































































































































Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды

Niveo NGSME48T4H, Руководство пользователя

Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды