Niveo NGSME48T4H Скачать руководство пользователя страница 93

Страница: 93 / 338

Chapter

3: Web Management

Security - Network - DHCP - Relay

PoE Switch User Manual | 93

VLAN Parameters

VLAN ID Filter

Specify the VLAN ID filter for this ACE.



Any:

No VLAN ID filter is specified. (VLAN ID filter status is "don't-care".)



Specific:

If you want to filter a specific VLAN ID with this ACE, choose this value. A

field for entering a VLAN ID number appears.

VLAN ID

When "Specific" is selected for the VLAN ID filter, you can enter a specific VLAN ID number.

The allowed range is 1 to 4095. A frame that hits this ACE matches this VLAN ID value.

Tag Priority

Specify the tag priority for this ACE. A frame that hits this ACE matches this tag priority. The

allowed number range is 0 to 7. The value Any means that no tag priority is specified (tag

priority is "don't-care".)

Содержание NGSME48T4H



















































































































































































































































































































































Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды

Niveo NGSME48T4H, Руководство пользователя

Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды