Niveo NGSME48T4H Скачать руководство пользователя страница 217

Страница: 217 / 338

Chapter

3: Web Management

Ports - Traffic Overview

PoE Switch User Manual | 217

3.2.3.2. Ports - Traffic Overview

This page provides an overview of general traffic statistics for all switch ports.

The ports belong to the currently selected stack unit, as reflected by the page header.

Port

The logical port for the settings contained in the same row.

Packets

The number of received and transmitted packets per port.

Bytes

The number of received and transmitted bytes per port.

Errors

The number of frames received in error and the number of incomplete transmissions per port.

Drops

The number of frames discarded due to ingress or egress congestion.

Filtered

The number of received frames filtered by the forwarding process.

Buttons



Refresh:

Click to refresh the page immediately.



Clear:

Clears the counters for all ports.



Auto-refresh:

Check this box to refresh the page automatically. Automatic refresh

occurs every 3 seconds.

Содержание NGSME48T4H



















































































































































































































































































































































Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды

Niveo NGSME48T4H, Руководство пользователя

Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды