Niveo NGSME48T4H Скачать руководство пользователя страница 250

Страница: 250 / 338

Chapter

3: Web Management

Security - AAA - RADIUS Overview

PoE Switch User Manual | 250

3.2.5.3. Security - Network

3.2.5.3.1. Security - AAA - RADIUS Overview

This page provides an overview of the status of the RADIUS servers configurable on the

Authentication configuration page.

RADIUS Authentication Servers

The RADIUS server number. Click to navigate to detailed statistics for this server.

IP Address

The IP address and UDP port number (in <IP Address>:<UDP Port> notation) of this

server.

Status

The current status of the server. This field takes one of the following values:



Disabled:

The server is disabled.



Not Ready:

The server is enabled, but IP communication is not yet up and running.



Ready:

The server is enabled, IP communication is up and running, and the RADIUS

module is ready to accept access attempts.



Dead (X seconds left):

Access attempts were made to this server, but it did not reply

within the configured timeout. The server has temporarily been disabled, but will get

re-enabled when the dead-time expires. The number of seconds left before this

occurs is displayed in parentheses. This state is only reachable when more than one

server is enabled.

RADIUS Accounting Servers

The RADIUS server number. Click to navigate to detailed statistics for this server.

Содержание NGSME48T4H



















































































































































































































































































































































Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды

Niveo NGSME48T4H, Руководство пользователя

Результаты поиска

Содержание NGSME48T4H

Отзывы:

Похожие инструкции для NGSME48T4H

Бренды по названию

Популярные бренды