Mitsubishi Electric PUHY-(E)P300 Скачать руководство пользователя

Страница: 94 / 302

[

VII

Control ]

- 85 -

HWE07010

(2) Address switch

Actual indoor unit address setting varies in different systems. Refer to the installation manual for the outdoor unit for details

on how to make the address setting.

Each address is set with a combination of the settings for the 10's digit and 1's digit.

(Example)
When setting the address to "3", set the 1's digit to 3, and the 10's digit to 0.

When setting the address to "25", set the 1's digit to 5, and the 10's digit to 2.

3. Function of the switch <Remote controller>
(1) MA remote controller (PAR-20MAA)

The SW is located at the bottom of the remote controller under the cover. Operate the switches to perform the remote con-

troller main/sub setting or other function settings. Normally, do not change the settings of switches other than the SW1 (main/

sub switching switch). (All the switches are set to "ON" at factory setting.)

The MA remote controller (PAR-21MAA) does not have the switches listed above. Refer to the installation manual for the func-

tion setting.

Remote controller

Switching switch

Switch

Function

Remote controller
main/sub setting

At power on of the
remote controller

Normal

startup

Timer mode

startup

Cooling/heating display
set by automatic setting

Displayed

Not displayed

Suction temperature display
(discharge temperature display)

Displayed

Not displayed

Operation by switch settings

Switch setting timing

OFF

Main

Sub

Before power on

When two remote controllers are connected
to one group, set either of the remote
controllers to "Sub".

When the program timer (only few stock
products are available) is connected, set to
"Timer mode startup" to resume the operation
with timer mode after power is restored.

When the automatic mode is set and the
"Cooling"/"Heating" display is not necessary,
set to "Not displayed".

When the suction temperature (discharge
temperature) display is not necessary,
set to "Not displayed".

Содержание PUHY-(E)P300















































































































































































































































































































Результаты поиска

Содержание PUHY-(E)P300

Отзывы:

Похожие инструкции для PUHY-(E)P300

Бренды по названию

Популярные бренды

Mitsubishi Electric PUHY-(E)P300, Руководство по обслуживанию

Результаты поиска

Содержание PUHY-(E)P300

Отзывы:

Похожие инструкции для PUHY-(E)P300

Бренды по названию

Популярные бренды