manualshive.com logo in svg

Mitsubishi Electric PUHY-(E)P300, Руководство по обслуживанию

Mitsubishi Electric PUHY-(E)P300 - это мощный и надежный системный блок кондиционирования воздуха. Для поддержания его работоспособности и эффективности, рекомендуется регулярное обслуживание согласно Service Handbook. Скачайте бесплатно руководство по эксплуатации на manualshive.com для подробной информации.

Поделиться
Скачать
background image

ii

 

HWE07010

GB

Safety Precautions

Œ

Before installing the unit, thoroughly read the following safety precautions.

Œ

Observe these safety precautions for your safety.

WARNING

This symbol is intended to alert the user to the presence of important instructions that must be followed to avoid 

the risk of serious injury or death.

CAUTION

This symbol is intended to alert the user to the presence of important instructions that must be followed to avoid 

the risk of serious injury or damage to the unit.

Œ

After reading this manual, give it to the user to retain for future reference.

Œ

Keep this manual for easy reference. When the unit is moved or repaired, give this manual to those who provide these 

services. 
When the user changes, make sure that the new user receives this manual.

WARNING

Ask your dealer or a qualified technician to install the 
unit.

Improper installation by the user may result in water leak-
age, electric shock, smoke, and/or fire.

Properly install the unit on a surface that can with-
stand the weight of the unit.

Unit installed on an unstable surface may fall and cause in-
jury.

Only use specified cables. Securely connect each ca-
ble so that the terminals do not carry the weight of the 
cable.

Improperly connected or fixed cables may produce heat 
and start a fire.

Take appropriate safety measures against strong 
winds and earthquakes to prevent the unit from falling.

If the unit is not installed properly, the unit may fall and 
cause serious injury to the person or damage to the unit.

Do not make any modifications or alterations to the 
unit. Consult your dealer for repair.

Improper repair may result in water leakage, electric shock, 
smoke, and/or fire.

Do not touch the heat exchanger fins.

The fins are sharp and dangerous.

In the event of a refrigerant leak, thoroughly ventilate 
the room.

If refrigerant gas leaks and comes in contact with an open 
flame, poisonous gases will be produced.

When installing the All-Fresh type units, take it into 
consideration that the outside air may be discharged 
directly into the room when the thermo is turned off.

Direct exposure to outdoor air may have an adverse effect 
on health. It may also result in food spoilage.

Properly install the unit according to the instructions 
in the installation manual.

Improper installation may result in water leakage, electric 
shock, smoke, and/or fire.

Have all electrical work performed by an authorized 
electrician according to the local regulations and in-
structions in this manual, and a dedicated circuit must 
be used.

Insufficient capacity of the power supply circuit or improper 
installation may result in malfunctions of the unit, electric 
shock, smoke, and/or fire.

Содержание PUHY-(E)P300















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PUHY-(E)P300

Dawlance Chrome Owner'S Manual preview
Chrome
Бренд: Dawlance Страницы: 8
Olimpia splendid Unico Twin Instructions For Installation, Use And Maintenance Manual preview
Unico Twin
Бренд: Olimpia splendid Страницы: 124
Gree CA145006400 Service Manual preview
CA145006400
Бренд: Gree Страницы: 73
Alfa Network Optigo CC Instruction Manual preview
Optigo CC
Бренд: Alfa Network Страницы: 28
Soleus Air KFMHP-18-ID Owner'S Manual preview
KFMHP-18-ID
Бренд: Soleus Air Страницы: 29
Zibro P 24 Operating Manual preview
P 24
Бренд: Zibro Страницы: 166
TCL 10T3E1 Let'S Get Started preview
10T3E1
Бренд: TCL Страницы: 33
Crosley 2020213A Use & Care Manual preview
2020213A
Бренд: Crosley Страницы: 8
Radialight AER Pro Operating Instructions Manual preview
AER Pro
Бренд: Radialight Страницы: 16
gmc aircon GMCAB15 User Manual preview
GMCAB15
Бренд: gmc aircon Страницы: 10
CIAT Splitciat SEO Manual preview
Splitciat SEO
Бренд: CIAT Страницы: 18
Prem-I-Air PJ152NP User Manual preview
PJ152NP
Бренд: Prem-I-Air Страницы: 8
REMKO RVD 1054 DC Assembly And Operating Instructions Manual preview
RVD 1054 DC
Бренд: REMKO Страницы: 88
Daikin 2AMK40FV1B Service Manual Removal Procedure preview
2AMK40FV1B
Бренд: Daikin Страницы: 29
Friedrich Twin Temp EQ08J11A Installation And Operation Manual preview
Twin Temp EQ08J11A
Бренд: Friedrich Страницы: 40
Haier ESA4089 Manuel preview
ESA4089
Бренд: Haier Страницы: 21
Haier ESA412J-115V Use & Care Manual preview
ESA412J-115V
Бренд: Haier Страницы: 44
Haier ESA408J Use And Care Manual preview
ESA408J
Бренд: Haier Страницы: 44

Бренды по названию

Популярные бренды

Загрузить еще бренды