Mitsubishi Electric PUHY-(E)P300 Скачать руководство пользователя страница 20

Страница: 20 / 302

[

Read Before Servicing ]

- 11 -

HWE07010

[9] Refrigerant Charging

1. Reasons

R410A is a pseudo-azeotropic HFC blend (boiling point R32=-52°C[-62°F], R125=-49°C[-52°F]) and can almost be handled

the same way as a single refrigerant, such as R22. To be safe, however, draw out the refrigerant from the cylinder in the liquid

phase. If the refrigerant in the gaseous phase is drawn out, the composition of the remaining refrigerant will change and be-

come unsuitable for use.

2. Notes

When using a cylinder with a siphon, refrigerant is charged in the liquid state without the need for turning it upside down. Check

the type of the cylinder on the label before use.

[10] Remedies to be taken in case of a Refrigerant Leak

If the refrigerant leaks out, it may be replenished. The entire refrigerant does not need to be replaced. (Charge refrigerant in the

liquid state.)

Refer to "IX [5] Refrigerant Leak".(page 241)

Cylinder with a siphon

Cylinder color R410A is pink.

Refrigerant charging in the liquid state

Cylin-
der

liquid

Valve

liquid

Cylin-
der

Cylinder without a siphon

Содержание PUHY-(E)P300















































































































































































































































































































Результаты поиска

Содержание PUHY-(E)P300

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi Electric PUHY-(E)P300, Руководство по обслуживанию

Результаты поиска

Содержание PUHY-(E)P300

Отзывы:

Бренды по названию

Популярные бренды