Mitsubishi Electric PUHY-(E)P300 Скачать руководство пользователя страница 180

Страница: 180 / 302

[

Troubleshooting ]

- 171 -

HWE07010

1. Error

Code

Power supply sync signal abnormality

2. Error

definition and error detection method

The frequency cannot be determined when the power is switched on.

3. Cause, check method and remedy

1. Error

Code

Motor abnormality

2. Error

definition and error detection method

LOSSNAY

∗

The motor keep running even if the power is OFF.

∗

The thermal overload relay is ON. (Only for the three-phase model)

Indoor unit

If detected less than 180rpm or more than 2000rpm, the indoor unit will restart and keep running for 3 minutes.If detected

again, the display will appear.

3. Cause, check method and remedy

4115

Cause

Check method and remedy

(1)

Power supply error

Check the voltage of the power supply terminal

block (TB1).

(2)

Noise filter problem

Coil problem

Circuit board failure

Check the coil connections.

Check for coil burnout.

Confirm that the voltage at the CN3 connector is

198 V or above.

(3)

Faulty wiring

Check fuse F01 on the control board.

(4)

Wiring failure

Between noise filter CN3 and noise filter CN2 and con-

trol board CNAC

Confirm that the voltage at the control board con-

nector CNAC is 198 V or above.

(5)

Control board failure

If none of the items described above is applicable,

and if the trouble reappears even after the power is

switched on again, replace the control board.

4116

Cause

Check method and remedy

(1)

Board failure

Replace the board.

(2)

Motor malfunction

Check for the motor and the solenoid switch.

(3)

Solenoid switch malfunction

Содержание PUHY-(E)P300















































































































































































































































































































Результаты поиска

Содержание PUHY-(E)P300

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi Electric PUHY-(E)P300, Руководство по обслуживанию

Результаты поиска

Содержание PUHY-(E)P300

Отзывы:

Бренды по названию

Популярные бренды