Mitsubishi Electric PUHY-(E)P300 Скачать руководство пользователя

Страница: 22 / 302

[

Read Before Servicing ]

- 13 -

HWE07010

[12] Notes on Refrigerating Machine Oil

1. Refrigerating machine oil in the HFC refrigerant system

HFC type refrigerants use a refrigerating machine oil different from that used in the R22 system.

Note that the ester oil used in the system has properties that are different from commercially available ester oil.

2. Effects of contaminants

Refrigerating machine oil used in the HFC system must be handled with special care to keep contaminants out.

The table below shows the effect of contaminants in the refrigerating machine oil on the refrigeration cycle.

3. The effects of contaminants in the refrigerating machine oil on the refrigeration cycle.

Refrigerant

Refrigerating machine oil

R22 Mineral

oil

R407C

Ester oil

R410A Ester

oil

*1. Contaminants is defined as moisture, air, processing oil, dust/dirt, wrong types of refrigerant, and refrigerating machine oil.

Cause

Symptoms

Effects on the refrigerant cycle

Water infiltration

Frozen expansion valve

and capillary tubes

Clogged expansion valve and capillary tubes

Poor cooling performance

Compressor overheat

Motor insulation failure

Burnt motor

Coppering of the orbiting scroll

Lock

Burn-in on the orbiting scroll

Hydrolysis

Sludge formation and ad-

hesion

Acid generation

Oxidization

Oil degradation

Air infiltration

Oxidization

Infiltration of

contaminants

Dust, dirt

Adhesion to expansion valve and capillary

tubes

Clogged expansion valve, capillary tubes, and

drier

Poor cooling performance

Compressor overheat

Infiltration of contaminants into the com-

pressor

Burn-in on the orbiting scroll

Mineral oil

etc.

Sludge formation and adhesion

Clogged expansion valve and capillary tubes

Poor cooling performance

Compressor overheat

Oil degradation

Burn-in on the orbiting scroll

Содержание PUHY-(E)P300















































































































































































































































































































Результаты поиска

Содержание PUHY-(E)P300

Отзывы:

Похожие инструкции для PUHY-(E)P300

Бренды по названию

Популярные бренды

Mitsubishi Electric PUHY-(E)P300, Руководство по обслуживанию

Результаты поиска

Содержание PUHY-(E)P300

Отзывы:

Похожие инструкции для PUHY-(E)P300

Бренды по названию

Популярные бренды