Mitsubishi Electric PUHY-(E)P300 Скачать руководство пользователя | Manualshive

Страница: 194 / 302

background image

[

IX

Troubleshooting ]

- 185 -

HWE07010

GB

1. Error

Code

Transmission processor hardware error

2. Error

definition and error detection method

Although "0" was surely transmitted by the transmission processor, "1" is displayed on the transmission line.

The address/attribute appeared on the display on the remote controller indicates the controller where an error oc-

curred.

3. Cause

1) When the wiring work of or the polarity of either the indoor or outdoor transmission line is performed or is changed while the

power is on, the transmitted data will collide, the wave shape will be changed, and an error will be detected.

2) Grounding fault of the transmission line
3) When grouping the indoor units that are connected to different outdoor units, the male power supply connectors on the multiple

outdoor units are connected to the female power supply switch connector (CN40).

4) When the power supply unit for transmission lines is used in the system connected with MELANS, the male power supply

connector is connected to the female power supply switch connector (CN40) on the outdoor unit.

5)   Controller failure of the source of the error
6)   When the transmission data is changed due to the noise on the transmission line
7)   Voltage is not applied on the transmission line for centralized control (in case of grouped indoor units connected to different

outdoor units or in case of the system connected with MELANS)

4. Check method and remedy

6602

NO

Tightly reconnect the male power

supply connector to the female

power supply switch connector (CN40).

YES

YES

YES

YES

YES

YES

NO

NO

NO

NO

Is the transmission line work
performed while the power is on?

Check the power source of the indoor unit.

188 / 253V?

Check the transmission line work is performed
and the shielded wire is treated properly.

Grounding fault or does the shielded
wire contact with the transmission line?

System ?

Faulty power source work

Improper transmission line work

Turn off the power source of outdoor/indoor
units, and turn them on again.

NO

Investigation into the
transmission line noise

Noise exist?

Controller failure of the
source of the error

*For the investigation method, follow
<Investigation method of transmission wave shape/noise>

Investigation into the
cause of the noise

Correct the error.

System with the power supply
unit for transmission lines

Is the male power supply connector
connected to the female power supply
switch connector (CN40) on only one
of the outdoor unit?

Is the male power supply connector
connected to the female power supply
switch connector (CN40) ?

Confirm that the power supply
connector on the outdoor
unit is not plugged into CN40.

Confirm that the power supply
connector on the outdoor
unit is not plugged into CN40.

Disconnect the male
power supply on
CN40 and connect it to CN41

Single-outdoor-unit system

Multiple-outdoor-unit system

«
...
192
193
194
195
196
...
»

Содержание PUHY-(E)P300















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PUHY-(E)P300

Бренд: INVENTOR Страницы: 76

VERT-I-PAK B-SERIES

Бренд: Friedrich Страницы: 20

GWH09ACC-S6DBA1A/O

Бренд: Gree Страницы: 123

Бренд: Vaporetto Страницы: 14

SCE-AC5100B460V

Бренд: Saginaw Control & Engineering Страницы: 14

Бренд: Gree Страницы: 44

IM-CKA-0501 A Series

Бренд: McQuay Страницы: 39

Бренд: York Страницы: 186

Бренд: TCL Страницы: 27

Бренд: Lennox Страницы: 28

Бренд: Lennox Страницы: 32

TA36FFLL-1232IA

Бренд: Tesla Страницы: 288

Бренд: Germ Guardian Страницы: 18

geoTHERM SERIES

Бренд: Vaillant Страницы: 56

Бренд: Panasonic Страницы: 68

Бренд: Haier Страницы: 100

Бренд: Samsung Страницы: 26

Бренд: Samsung Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды