Mitsubishi Electric PUHY-(E)P300 страница 220 Скачать руководство пользователя

Страница: 220 / 302

[

Troubleshooting ]

- 211 -

HWE07010

In case of M-NET remote controller

1. Phenomena

When the remote controller operation SW is turned on, a temporary operation display is indicated, and the display lights out

immediately.

2. Cause
(1) The power is not supplied to the indoor unit.

The main power of the indoor unit (AC220V) is not on.

The connector on the indoor unit board has come off.

The fuse on the indoor unit board has melted.

Transformer failure and disconnected wire of the indoor unit

The indoor unit board failure

(2) The outdoor control board failure

As the indoor unit does not interact with the outdoor unit, the outdoor unit model cannot be recognized.

3. Check method and remedy

YES

Check LED1 on the

indoor unit control board.

Is it lit?

When it is lit

When it is off
or cannot be checked

Check for the change of LED
display by operating dip
switch SW1 for self-diagnosis.

Check voltage of the power supply
terminal on the indoor unit.

AC220V?

Check the fuse on
the circuit board.

Melted?

Check 200V circuit for
short circuit and ground fault

Check the connection
of the connector.

Check the main power of

the power supply wire

Turn on the
power again.

Connector contact failure

Disconnected?

Check the resistance value

of the transformer

Within specification?

Check the cause of the
disconnected transformer.
Ground fault on the circuit board
Ground fault of the sensor and the LEV

Check self-diagnosis function

of outdoor unit

Changed?

Outdoor unit board failure

Check self-diagnosis function of
outdoor unit after the power on.

Accidental
error

Indoor unit control
board failure

Correct
the error.

*1. Refer to the parts catalog “transformer check”.

Содержание PUHY-(E)P300















































































































































































































































































































Результаты поиска

Содержание PUHY-(E)P300

Отзывы:

Похожие инструкции для PUHY-(E)P300

Бренды по названию

Популярные бренды

Mitsubishi Electric PUHY-(E)P300, Руководство по обслуживанию

Результаты поиска

Содержание PUHY-(E)P300

Отзывы:

Похожие инструкции для PUHY-(E)P300

Бренды по названию

Популярные бренды