Mitsubishi Electric PUHY-(E)P300 Скачать руководство пользователя страница 202

Страница: 202 / 302

[

Troubleshooting ]

- 193 -

HWE07010

1. Error

Code

No ACK abnormality

2. Error

definition and error detection method

The error is detected when no acknowledgement (ACK signal) is received after the transmission. (eg. When the data is trans-

mitted six times in a row with 30 seconds interval, the error is detected on the transmission side.)

The address/attribute appeared on the display on the remote controller indicates the controller which did not provide

the response (ACK).

3. System

configuration

(3) System connected to the system controllers (MELANS)

6607

Error

source

address

Error display

Detection

method

Cause

Check method and remedy

System

controller

(SC)

M-NET re-

mote controller

(RC)

MA remote

controller

(MA)

No acknowl-

edgement

(ACK) at IC

transmission to

Error display on some displays on

M-NET remote controllers

Check (1) - (3) on the left.

(1) Faulty wiring of the transmission

line for M-NET remote controller

(2) Disconnection or contact failure of

the transmission connector for M-

NET remote controller

(3) M-NET remote controller failure

Error occurrence on all IC in the

system with one outdoor unit

1) Check the LED display for

troubleshooting on the out-

door unit.

(1) An error is found by the outdoor

unit.

Total capacity error (7100)

Capacity code error (7101)

Error in the number of connected

units (7102)

Address setting error (7105)

If an error is found, check

the check code definition,

and correct the error.

If no error is found, check

the cause 2)

(2) Disconnection or short circuit of the

transmission line for the outdoor

unit on the terminal block for cen-

tralized control line connection

(TB7)

2) Check (2) - (4) on the left.

(3) Turn off the power source of the

outdoor unit

(4) Malfunction of electrical system for

the outdoor unit

Error display on all displays on M-

NET remote controllers

Check (1) - (4) on the left

(1) Same causes as (1) - (4) described

in 2.

(2) When the power supply unit for

transmission lines is used and the

male power supply connector is

connected to the female power sup-

ply switch connector (CN40) for the

transmission line for centralized

control

(3) Disconnection or shutdown of the

power source of the power supply

unit for transmission line

(4) System controller (MELANS) mal-

function

Содержание PUHY-(E)P300















































































































































































































































































































Результаты поиска

Содержание PUHY-(E)P300

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi Electric PUHY-(E)P300, Руководство по обслуживанию

Результаты поиска

Содержание PUHY-(E)P300

Отзывы:

Бренды по названию

Популярные бренды