Mitsubishi Electric PUHY-(E)P300 Скачать руководство пользователя

Страница: 176 / 302

[

Troubleshooting ]

- 167 -

HWE07010

1. Error

Code

Drain sensor (Thd) abnormality

2. Error

definition and error detection method

If the open or short circuit of the thermistor has been detected for 30 seconds, this condition is considered to be a preliminary

error, and the unit goes into the 3-minute restart delay mode.

If another episode of the above condition is detected during the preliminary error, this is considered a drain sensor error.(If

the short or open circuit of the thermistor is no longer detected, normal operation will be restored in 3 minutes.)

This error is detected when one of the following conditions are met.

∗

During Cool/Dry operation

∗

Liquid pipe temperature minus inlet temperature is equal to or smaller than - 10K (except during the defrost cycle)

∗

When the liquid temperature thermistor or suction temperature thermistor or short or open circuited.

∗

Drain pump is in operation.

∗

One hour has elapsed since the drain sensor went off.

Short: 90 °C [194 °F] or above

Open: - 20 °C [-4 °F] or below

3. Cause, check method and remedy

2503

Cause

Check method and remedy

(1)

Faulty connector (CN31) insertion.

Check for connector connection failure.

Reinsert the connector, restart the operation, and check for

proper operation.

(2)

Broken or semi-broken thermistor wire

Check for a broken thermistor wire.

(3)

Thermistor failure

Check the resistance of the thermistor.

0°C[32 °F]:6.0k

10°C[50 °F]:3.9k

20°C[68°F]:2.6k

30°C[86°F]:1.8k

40°C[104 °F]:1.3k

(4)

Indoor unit control board (error detection circuit)

failure

Replace the indoor unit control board if the problem recurs

when the unit is operated with the No.-1 and No.-2 pins on

the drain sensor connector (CN31) being short-circuited.

If the above item checks out OK, there are no problems with

the drain sensor.

Turn off the power and turn it back on.

Содержание PUHY-(E)P300















































































































































































































































































































Результаты поиска

Содержание PUHY-(E)P300

Отзывы:

Похожие инструкции для PUHY-(E)P300

Бренды по названию

Популярные бренды

Mitsubishi Electric PUHY-(E)P300, Руководство по обслуживанию

Результаты поиска

Содержание PUHY-(E)P300

Отзывы:

Похожие инструкции для PUHY-(E)P300

Бренды по названию

Популярные бренды