Mitsubishi Electric PUHY-(E)P300 Скачать руководство пользователя

Страница: 171 / 302

[

Troubleshooting ]

- 162 -

HWE07010

1. Error

Code

Abnormal high pressure 2 (outdoor unit)

2. Error

definition and error detection method

If the pressure of 0.098MPa [14psi] or lower is registered on the pressure sensor immediately before start-up, it will

trigger an abnormal stop, and error code "1302" will be displayed.

3. Cause, check method and remedy

1. Error

Code

Refrigerant overcharge

2. Error

definition and error detection method

An error can be detected by the discharge temperature superheat.

1) If the formula "TdSH 10K [18°F]" is satisfied during operation (first detection), the outdoor unit stops, goes into the 3-minute

restart mode, and starts up in three minutes.

2) If the formula "TdSH 10K [18°F]" is satisfied again within 30 minutes of the first stoppage of the outdoor unit (second de-

tection), the unit comes to an abnormal stop, and the error code "1500" appears.

3) If the formula "TdSH 10K [18°F]" is satisfied 30 minutes or more after the first stoppage of the outdoor unit, the same se-

quence as Item "1 above (first detection) is followed.

4) For 30 minutes after the stop of the outdoor unit, preliminary errors will be displayed on the LED display.

3. Cause, check method and remedy

1302

Cause

Check method and remedy

(1)

Inner pressure drop due to a leakage.

Refer to the page on the troubleshooting of the high

pressure sensor.(page 222)

(2)

Pressure sensor failure

(3)

Shorted-circuited pressure sensor cable due to torn

outer rubber

(4)

A pin on the male connector on the pressure sensor

is missing or contact failure

(5)

Disconnected pressure sensor cable

(6)

Failure of the pressure sensor input circuit on the

controller board

1500

Cause

Check method and remedy

(1)

Overcharged refrigerant

Refer to the page on refrigerant amount

evaluation.(page 109)

(2)

Thermistor input circuit failure on the control board

Check the temperature and pressure readings on the sen-

sor that are displayed on the LED monitor.

(3)

Faulty mounting of thermistor (TH4)

Check the temperature and pressure readings on the ther-

mistor that are displayed on the LED monitor.

(4)

Outdoor unit LEV2a, b actuation failure -> Heating

Refer to the section on troubleshooting the LEV.

(page 226)

Содержание PUHY-(E)P300















































































































































































































































































































Результаты поиска

Содержание PUHY-(E)P300

Отзывы:

Похожие инструкции для PUHY-(E)P300

Бренды по названию

Популярные бренды

Mitsubishi Electric PUHY-(E)P300, Руководство по обслуживанию

Результаты поиска

Содержание PUHY-(E)P300

Отзывы:

Похожие инструкции для PUHY-(E)P300

Бренды по названию

Популярные бренды