Mitsubishi Electric PUHY-(E)P300 страница 201 Скачать руководство пользователя

Страница: 201 / 302

[

Troubleshooting ]

- 192 -

HWE07010

1. Error

Code

No ACK abnormality

2. Error

definition and error detection method

The error is detected when no acknowledgement (ACK signal) is received after the transmission. (eg. When the data is trans-

mitted six times in a row with 30 seconds interval, the error is detected on the transmission side.)

The address/attribute appeared on the display on the remote controller indicates the controller which did not provide

the response (ACK).

3. System

configuration

(3) System connected to the system controllers (MELANS)

6607

Error

source

address

Error display

Detection

method

Cause

Check method and remedy

M-NET re-

mote con-

troller

(RC)

M-NET re-

mote controller

(RC)

System con-

troller (SC)

MA remote

controller (MA)

No acknowl-

edgement

(ACK) at IC

transmission to

Same as grouping of units in a sys-

tem with multiple outdoor units

Same remedy as that for

grouping of units in a system

with multiple outdoor units

System con-

troller

(SC)

No acknowl-

edgement

(ACK) at

MELANS

transmission to

Error occurrence on some IC

Same remedy as that for

system with one outdoor unit

(1) Same cause as that for system

with one outdoor unit

Error occurrence on all IC in the

system with one outdoor unit

1) Check the LED display for

troubleshooting on the out-

door unit.

(1) An error is found by the outdoor

unit.

Total capacity error (7100)

Capacity code error (7101)

Error in the number of connected

units (7102)

Address setting error (7105)

If an error is found, check

the check code definition,

and correct the error.

If no error is found, check

the cause 2).

(2) Disconnection or short circuit of the

transmission line for the outdoor

unit on the terminal block for cen-

tralized control line connection

(TB7)

2) Check (2) - (4) on the left.

(3) Turn off the power source of the

outdoor unit

(4) Malfunction of electrical system for

the outdoor unit

Error occurrence on all IC

Check (1) - (4) on the left.

(1) Same causes as (1) - (4) described

in 2.

(2) When the power supply unit for

transmission lines is used and the

male power supply connector is

connected to the female power

supply switch connector (CN40) for

the transmission line for central-

ized control

(3) Disconnection or shutdown of the

power source of the power supply

unit for transmission line

(4) System controller (MELANS) mal-

function

Содержание PUHY-(E)P300















































































































































































































































































































Результаты поиска

Содержание PUHY-(E)P300

Отзывы:

Похожие инструкции для PUHY-(E)P300

Бренды по названию

Популярные бренды

Mitsubishi Electric PUHY-(E)P300, Руководство по обслуживанию

Результаты поиска

Содержание PUHY-(E)P300

Отзывы:

Похожие инструкции для PUHY-(E)P300

Бренды по названию

Популярные бренды