Mitsubishi Electric PUHY-(E)P300 Скачать руководство пользователя

Страница: 122 / 302

[

VIII

Test Run Mode ]

- 113 -

HWE07010

CAUTION

Do not release the extracted refrigerant into the air.

CAUTION

Charge liquid refrigerant (as opposed to gaseous refrigerant) into the system.

If gaseous refrigerant is charged into the system, the composition of the refrigerant in the cylinder will change and may

result in performance loss.

YES

Start

Put all indoor units in the test run mode
and run the units in cooling mode.

Has it been at least

30 minutes since

start up?

Note 3

Note 1

Does 8K [14 F] Tc-TH3

12K [22 F] hold true?

(Use the largest “Tc - TH3” value of the

OC, OS1, and OS2.)

Does the following hold true?

Tc-TH3

8K [14°F]

*Refer to the previous page for *Notes 1-4 in the chart.

Note 2

Note 1

Gradually add refrigerant from
the service port on the low-
pressure side.

Keep the unit running for 5 minutes after
adjusting the refrigerant amount to
determine its adequacy.

Keep the unit running for 5 minutes after adjusting the
refrigerant amount to determine its adequacy.

Turn off SW4-3 on the OC.

Turn on SW4-3 on the OC.

Adjustment complete

Note 4

Has the initial start-up

mode been completed?

Gradually add refrigerant from
the service port on the low
pressure side.

Keep the unit running for 5 minutes
after adjusting the refrigerant amount
and check(Tc-TH3)

Gradually add refrigerant from
the service port on the low
pressure side.

Gradually draw out
refrigerant from the service
port on the low pressure side.

Does Tc-TH6

20K [36 F] hold true?

Is the TH4 value of the OC, OS1,

OS2 at or below 100 C [212 F]?

Has the operating frequency

of the compressor on the OC, OS1,

and OS2 become stable?

ote

Is the TH4 value of the OC, OS1,

OS2 at or below 95 C [203 F]

(Check this item on the unit whose “Tc – TH3” value was

used in the step above.)

Содержание PUHY-(E)P300















































































































































































































































































































Результаты поиска

Содержание PUHY-(E)P300

Отзывы:

Похожие инструкции для PUHY-(E)P300

Бренды по названию

Популярные бренды

Mitsubishi Electric PUHY-(E)P300, Руководство по обслуживанию

Результаты поиска

Содержание PUHY-(E)P300

Отзывы:

Похожие инструкции для PUHY-(E)P300

Бренды по названию

Популярные бренды