Mitsubishi Electric PUHY-(E)P300 Скачать руководство пользователя

Страница: 238 / 302

[

Troubleshooting ]

- 229 -

HWE07010

(4) Outdoor unit LEV (LEV1) coil removal procedure

1) LEV component

As shown in the figure, the outdoor LEV is made in such a way that the coils and the body can be separated.

2) Removing the coils

Fasten the body tightly at the bottom (Part A in the figure) so that the body will not move, then pull out the coils toward the

top.If the coils are pulled out without the body gripped, undue force will be applied and the pipe will be bent.

3) Installing the coils

Fix the body tightly at the bottom (Part A in the figure) so that the body will not move, then insert the coils from the top, and

insert the coil stopper securely in the pipe on the body. Hold the body when pulling out the coils to prevent so that the pipe

will not be bent.

If the coils are pushed without the body gripped, undue force will be applied and the pipe will be bent. Hold the body when

pulling out the coils to prevent so that the pipe will not be bent.

Coils

Stopper

Lead wire

Body

Part A

Содержание PUHY-(E)P300















































































































































































































































































































Результаты поиска

Содержание PUHY-(E)P300

Отзывы:

Похожие инструкции для PUHY-(E)P300

Бренды по названию

Популярные бренды

Mitsubishi Electric PUHY-(E)P300, Руководство по обслуживанию

Результаты поиска

Содержание PUHY-(E)P300

Отзывы:

Похожие инструкции для PUHY-(E)P300

Бренды по названию

Популярные бренды