manualshive.com logo in svg

Mitsubishi Electric PUHY-(E)P300, Руководство по обслуживанию

Mitsubishi Electric PUHY-(E)P300 - это мощный и надежный системный блок кондиционирования воздуха. Для поддержания его работоспособности и эффективности, рекомендуется регулярное обслуживание согласно Service Handbook. Скачайте бесплатно руководство по эксплуатации на manualshive.com для подробной информации.

Поделиться
Скачать
background image

[ 

IX 

 Troubleshooting ] 

- 241 -

HWE07010

GB

[5] Refrigerant Leak

1.  Leak spot: In the case of extension pipe for indoor unit (Cooling season)

1)   Mount a pressure gauge on the service check joint (CJ2) on the low-pressure side.
2)   Stop all the indoor units, and close the liquid service valve (BV2) inside the outdoor unit while the compressor is being stopped.
3)   Stop all the indoor units; turn on SW2-4 on the outdoor unit control board while the compressor is being stopped.(Pump down 

mode will start, and all the indoor units will run in cooling test run mode.)

4)   In the pump down mode (SW2-4 is ON), all the indoor units will automatically stop when the low pressure (63LS) reaches 

0.383MPa [55psi] or less or 15 minutes have passed after the pump mode started. Stop all the indoor units and compressors 
when the pressure indicated by the pressure gauge, which is on the check joint (CJ2) for low-pressure service, reaches 
0.383MPa [55psi] or 20 minutes pass after the pump down operation is started.

5)   Close the gas service valve (BV1) inside the outdoor unit.
6)   Collect the refrigerant that remains in the extended pipe for the indoor unit. Do not discharge refrigerant into the atmosphere 

when it is collected.

7)   Repair the leak.
8)   After repairing the leak, vacuum the extension pipe and the indoor unit.
9)   To adjust refrigerant amount, open the service valves (BV1 and BV2) inside the outdoor unit and turn off SW2-4.

2.  Leak spot: In the case of outdoor unit (Cooling season)
(1) Run all the indoor units in the cooling test run mode.

1)   To run the indoor unit in test run mode, turn SW3-2 from ON to OFF when SW3-1 on the outdoor control board is ON.
2)   Change the setting of the remote controller for all the indoor units to the cooling mode.
3)   Check that all the indoor units are performing a cooling operation.

(2)  Check the values of Tc and TH6.

(To display the values on the LED screen, use the self-diagnosis switch (SW1) on the outdoor unit control board.)

1)   When Tc-TH6 is 10K [18°F] or more : See the next item (3).
2)   When Tc-TH6 is less than 10K [18°F] :  After the compressor stops, collect the refrigerant inside the system, repair the leak, 

perform evacuation, and recharge new refrigerant. (Leak spot: 4. In the case of outdoor unit, handle in the same way as heat-
ing season.)

(3)  Stop all the indoor units, and stop the compressor.

1)   To stop all the indoor units and the compressors, turn SW3-2 from ON to OFF when SW3-1 on the outdoor control board is ON.
2)   Check that all the indoor units are being stopped.

(4)  Close the service valves (BV1 and BV2).
(5)  To prevent the liquid seal, extract small amount of refrigerant from the check joint of the liquid service valve (BV2), 

as the liquid seal may cause a malfunction of the unit.

(6)  Collect the refrigerant that remains inside the outdoor unit.Do not discharge refrigerant into air into the atmosphere 

when it is collected.

(7) Repair the leak.
(8)  After repairing the leak, replace the dryer with the new one, and perform evacuation inside the outdoor unit.
(9)  To adjust refrigerant amount, open the service valves (BV1 and BV2) inside the outdoor unit.

When the power to the outdoor/indoor unit must be turned off to repair the leak after closing the service valves specified in 

the item 4, turn the power off in approximately one hour after the outdoor/indoor units stop.

1)   When 30 minutes have passed after the item 4 above, the indoor unit lev turns from fully closed to slightly open to prevent the 

refrigerant seal.
LEV2a and LEV2b open when the outdoor unit remains stopped for 15 minutes to allow for the collection of refrigerant in the 
outdoor unit heat exchanger and to enable the evacuation of the outdoor unit heat exchanger.
If the power is turned of in less than 5 minutes, LEV2a and LEV2b may close, trapping high-pressure refrigerant in the outdoor 
unit heat exchanger and creating a highly dangerous situation.

2)   Therefore, if the power source is turned off within 30 minutes, the lev remains fully closed and the refrigerant remains sealed.

When only the power for the indoor unit is turned off, the indoor unit LEV turns from faintly open to fully closed.

Tc self-diagnosis switch

TH3 self-diagnosis switch

ON

1 2 3 4 5 6 7 8 9 10

SW1

1 2 3 4 5 6 7 8 9 10

ON

SW1

Содержание PUHY-(E)P300















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PUHY-(E)P300

GE AJEM12DCD Owner'S Manual & Installation Instructions preview
AJEM12DCD
Бренд: GE Страницы: 72
Haier AW07LC2VHA Technical Overview preview
AW07LC2VHA
Бренд: Haier Страницы: 122
Black + Decker BPT05WTB Instruction Manual preview
BPT05WTB
Бренд: Black + Decker Страницы: 84
Bryant 619ENF Installation, Start-Up And Service Instructions Manual preview
619ENF
Бренд: Bryant Страницы: 16
Jocel JACP9030733 Instruction Manual preview
JACP9030733
Бренд: Jocel Страницы: 72
Zamil PS036 Installation, Operation & Maintenance Manual preview
PS036
Бренд: Zamil Страницы: 51
Goodman GSC13 SEER Technical Manual preview
GSC13 SEER
Бренд: Goodman Страницы: 48
Gree CV010002400 Service Manual preview
CV010002400
Бренд: Gree Страницы: 37
York EVKC 18 DSAAAR Installation Instructions Manual preview
EVKC 18 DSAAAR
Бренд: York Страницы: 16
ACPro AULD36W2/A-D Owner'S Manual preview
AULD36W2/A-D
Бренд: ACPro Страницы: 41
Lennox XC13 018 Unit Information preview
XC13 018
Бренд: Lennox Страницы: 14
Daikin FTXG25CVMAS Operation Manual preview
FTXG25CVMAS
Бренд: Daikin Страницы: 30
Clatronic CL 3672 Instruction Manual preview
CL 3672
Бренд: Clatronic Страницы: 54
ICP NAC248AKA1 Installation Instructions Manual preview
NAC248AKA1
Бренд: ICP Страницы: 12
Qlima S 7035 Operating Manual preview
S 7035
Бренд: Qlima Страницы: 130
Daikin FTXM20W2VMA Operation Manual preview
FTXM20W2VMA
Бренд: Daikin Страницы: 96
Daikin FTXM20WVMA Operation Manual preview
FTXM20WVMA
Бренд: Daikin Страницы: 96
Daikin FTXM25QVMA Operation Manual preview
FTXM25QVMA
Бренд: Daikin Страницы: 40

Бренды по названию

Популярные бренды

Загрузить еще бренды