Mitsubishi Electric PUHY-(E)P300 Скачать руководство пользователя

Страница: 189 / 302

[

Troubleshooting ]

- 180 -

HWE07010

1. Error

Code

Heat sink failure (Detail code 01)

2. Error

definition and error detection method

When a short or an open of THHS is detected just before or during the inverter operation.

3. Cause, check method and remedy

Refer to section - 6 - "Inverter" under part [4] "Trouble shooting principal parts" for error codes related to the

inverter.(page 232)

1. Error

Code

High pressure sensor failure (outdoor unit)

2. Error

definition and error detection method

If the high pressure sensor detects 0.098MPa [14psi] or less during the operation, the outdoor unit stops once, turns to anti-

restart mode for 3 minutes, and restarts after 3 minutes when the detected high pressure sensor is 0.098MPa [14psi] or more.

If the high pressure sensor detects 0.098MPa [14psi] or less just before the restart, the outdoor unit makes an error stop, and

the error code "5201" will appear.

During 3-minute antirestart mode, preliminary errors will be displayed on the LED display.

A error is not detected for 3 minutes after the compressor start, during defrost operation, or 3 minutes after defrost operation.

3. Cause, check method and remedy

5110

Cause

Check method and remedy

(1)

INV board failure

If the problem recurs when the unit is put into operation, replace

the INV board.

5201

Cause

Check method and remedy

(1)

High pressure sensor failure

Refer to the page on the troubleshooting of

the high pressure sensor.

(9 [4] -1-(page 222))

(2)

Pressure drop due to refrigerant leak

(3)

Torn wire coating

(4)

A pin on the male connector is missing or contact failure

(5)

Disconnected wire

(6)

High pressure sensor input circuit failure on the control board

Содержание PUHY-(E)P300















































































































































































































































































































Результаты поиска

Содержание PUHY-(E)P300

Отзывы:

Похожие инструкции для PUHY-(E)P300

Бренды по названию

Популярные бренды

Mitsubishi Electric PUHY-(E)P300, Руководство по обслуживанию

Результаты поиска

Содержание PUHY-(E)P300

Отзывы:

Похожие инструкции для PUHY-(E)P300

Бренды по названию

Популярные бренды