Mitsubishi Electric PUHY-(E)P300 Скачать руководство пользователя страница 242

Страница: 242 / 302

[

Troubleshooting ]

- 233 -

HWE07010

Error display/failure condition

Measure/inspection item

[1]

Inverter related errors

4250, 4255, 4220, 4225, 4230, 4240,4260, 5301, 0403

Check the details of the inverter error in the error log at 10.[1] Table of

LED codes.

Take appropriate measures to the error code and the error details in ac-

cordance with 9. [2] Self-diagnosis on the basis of Error Display on Re-

mote Controller and Remedy for Error.

[2]

Main power breaker trip

Refer to "(3) Trouble treatment when the main power breaker is

tripped".(page 236)

[3]

Main power earth leakage breaker trip

Refer to "(4) Trouble treatment when the main power earth leakage

breaker is tripped".(page 236)

[4]

Only the compressor does not operate.

Check the inverter frequency on the LED monitor and proceed to (2) -

[4] if the compressor is in operation.(page 235)

[5]

The compressor vibrates violently at all times or makes an abnor-

mal sound.

See (2)-[4].(page 235)

[6]

Only the fan motor does not operate.

Check the inverter frequency on the LED monitor and proceed to (2)-

[6] if the fan motor is in operation.(page 235)

[7]

The fan motor shakes violently at all times or makes an abnormal

sound.

Check the inverter frequency on the LED monitor and proceed to (2)-

[6] if the fan motor is in operation.(page 235)

[8]

Noise is picked up by the peripheral device

<1> Check that power supply wiring of the peripheral device does not

run close to the power supply wiring of the outdoor unit.

<2> Check if the inverter output wiring is not running parallel to the

power supply wiring and the transmission lines.

<3> Check that the shielded wire is used as the transmission line when

it is required, and check that the grounding work is performed prop-

erly on the shielded wire.

<4> Meg failure for electrical system other than the inverter

<5> Attach a ferrite core to the inverter output wiring. (Contact the fac-

tory for details of the service part settings.)

<6> Provide separate power supply to the air conditioner and other

electric appliances.

<7> If the error occurred suddenly, a ground fault of the inverter output

can be considered. See (2)-[4].(page 235)

*Contact the factory for cases other than those listed above.

[9]

Sudden malfunction (as a result of external noise.)

<1> Check that the grounding work is performed properly.

<2>Check that the shielded wire is used as the transmission line when

it is required, and check that the grounding work is performed prop-

erly on the shielded wire.

<3>Check that neither the transmission line nor the external connec-

tion wiring does not run close to another power supply system or

does not run through the same conduit pipe.

* Contact the factory for cases other than those listed above.

Содержание PUHY-(E)P300















































































































































































































































































































Результаты поиска

Содержание PUHY-(E)P300

Отзывы:

Бренды по названию

Популярные бренды

Mitsubishi Electric PUHY-(E)P300, Руководство по обслуживанию

Результаты поиска

Содержание PUHY-(E)P300

Отзывы:

Бренды по названию

Популярные бренды