Mitsubishi Electric PUHY-(E)P300 Скачать руководство пользователя

Страница: 123 / 302

[

VIII

Test Run Mode ]

- 114 -

HWE07010

[6] The following symptoms are normal

Symptoms

Remote controller

display

Cause

The indoor unit does not start

after starting cooling (heating)

operation.

"Cooling (heating)"

icon blinks on the

display.

The unit cannot perform a heating (cooling) operation when other indoor

units are performing a cooling (heating) operation.

The auto vane adjusts its posi-

tion by itself.

Normal display

After an hour of cooling operation with the auto vane in the vertical posi-

tion, the vane may automatically move into the horizontal position.

Louver blades will automatically move into the horizontal position while

the unit is in the defrost mode, pre-heating stand-by mode, or when the

thermostat triggers unit off.

The fan stops during heating

operation.

Defrost

The fan remains stopped during defrost operation.

The fan keeps running after

the unit has stopped.

Display is off.

When the auxiliary heater is turned on, the fan operates for one minute

after stopping to dissipate heat.

The fan speed does not reach

the set speed when operation

switch is turned on.

STAND BY

The fan operates at extra low speed for 5 minutes after it is turned on or

until the pipe temperature reaches 35°C[95°F], then it operates at low

speed for 2 minutes, and finally it operates at the set speed.

(Pre-heating stand-by)

When the main power is

turned on, the display shown

on the right appears on the in-

door unit remote controller for

5 minutes.

"HO" or "PLEASE

WAIT" icons blink

on the display.

The system is starting up. Wait until the blinking display of "HO" or

"PLEASE WAIT" go off.

The drain pump keeps run-

ning after the unit has

stopped.

Unlit

The drain pump stays in operation for three minutes after the unit in the

cooling mode is stopped.

The drain pump is running

while the unit is stopped.

When drain water is detected, the drain pump goes into operation even

while the unit is stopped.

Indoor unit and BC controller

make noise during cooling/

heating changeover.

Normal display

This noise is made when the refrigerant circuit is reversed and is normal.

Sound of the refrigerant flow is

heard from the indoor unit im-

mediately after starting opera-

tion.

Normal display

This is caused by the transient instability of the refrigerant flow and is nor-

mal.

Warm air sometimes comes

out of the indoor units that are

not in the heating mode.

Normal display

This is due to the fact that the LEVs on some of the indoor units are kept

slightly open to prevent the refrigerant in the indoor units that are not op-

erating in the heating mode from liquefying and accumulating in the com-

pressor. It is part of a normal operation.

Содержание PUHY-(E)P300















































































































































































































































































































Результаты поиска

Содержание PUHY-(E)P300

Отзывы:

Похожие инструкции для PUHY-(E)P300

Бренды по названию

Популярные бренды

Mitsubishi Electric PUHY-(E)P300, Руководство по обслуживанию

Результаты поиска

Содержание PUHY-(E)P300

Отзывы:

Похожие инструкции для PUHY-(E)P300

Бренды по названию

Популярные бренды