Lenovo ThinkServer TD350 Скачать руководство пользователя страница 158

Страница: 158 / 226

7. Gently press the microprocessor retainer as shown to open it. Ensure that the small handles and the

microprocessor retainer are in the fully open position.

Figure 106. Opening the microprocessor retainer

8. Touch only the edges of the microprocessor and carefully lift it straight up and out of the microprocessor

socket. Place the old microprocessor on a static-protective surface.

Notes:

• Do not touch the gold contacts on the bottom of the microprocessor.

• Do not drop anything onto the microprocessor socket while it is exposed. The socket pins must be

kept as clean as possible.

Figure 107. Removing the microprocessor

9. Touch the static-protective package that contains the new microprocessor to any unpainted surface on

the outside of the server. Then, remove the new microprocessor from the package.

144

ThinkServer TD350 User Guide and Hardware Maintenance Manual

Содержание ThinkServer TD350



































































































































































































































Результаты поиска

Содержание ThinkServer TD350

Отзывы:

Похожие инструкции для ThinkServer TD350

Бренды по названию

Популярные бренды

Lenovo ThinkServer TD350, Руководство пользователя и руководство по техническому обслуживанию аппаратного обеспечения

Результаты поиска

Содержание ThinkServer TD350

Отзывы:

Похожие инструкции для ThinkServer TD350

Бренды по названию

Популярные бренды