Lenovo ThinkServer TD350 Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 226

Lenovo ThinkServer TD350 Скачать руководство пользователя страница 117

6. Do one of the following:

• If you are installing the RAID 510i upgrade key, insert the key into the RAID upgrade key connector on

the RAID 510i AnyRAID adapter. Ensure that the key is securely seated.

• If you are installing the RAID 520i upgrade key, insert the key into the J3 connector on the RAID 520i

PCIe adapter. Ensure that the key is securely seated.

Figure 61. Installing the RAID 510i upgrade key

7. Reinstall the RAID 510i AnyRAID adapter or the RAID 520i PCIe adapter if you have removed it.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation, go to “Completing the parts replacement” on page 180. Then, the hardware

RAID 5 and RAID 50 levels are available for your server if your server has the required number of storage
drives installed. For information about how to configure the hardware RAID, refer to the

MegaRAID SAS

Software User Guide

on the documentation disc that comes with your server.

Removing the RAID upgrade key

Attention:

Do not open your server or attempt any repair before reading and understanding “Read this first: safety

information” on page iii and “Guidelines” on page 69.

Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.

Notes:

• Removing the RAID upgrade key might impact your RAID configurations. Back up your data before you

begin to avoid any data loss due to a RAID configuration change.

• If you remove the RAID upgrade key, the hardware RAID 5 and RAID 50 will be disabled.

• Use any documentation that comes with the RAID upgrade key and follow those instructions in addition to

the instructions in this topic.

To remove the RAID upgrade key, do the following:

1. Remove all external media from the drives and turn off all attached devices and the server. Then,

disconnect all power cords from electrical outlets and disconnect all cables that are connected to
the server.

Replacing hardware

103

«
...
115
116
117
118
119
...
»

Содержание ThinkServer TD350



































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды