manualshive.com logo in svg
  • Главная
  • /
  • Lenovo
  • /
  • ThinkServer TD350
  • /
  • Руководство пользователя и руководство по техническому обслуживанию аппаратного обеспечения

Lenovo ThinkServer TD350, Руководство пользователя и руководство по техническому обслуживанию аппаратного обеспечения

Lenovo ThinkServer TD350 - надежный сервер с высокой производительностью. Чтобы узнать как правильно установить и обслуживать его, скачайте бесплатные Руководство пользователя и Руководство по обслуживанию оборудования с manualshive.com. Никогда не было проще получить доступ к необходимой информации для успешной работы вашего сервера.

Поделиться
Скачать
background image

1. Remove all external media from the drives and turn off all attached devices and the server. Then,

disconnect all power cords from electrical outlets and disconnect all cables that are connected to
the server.

2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,

clean, and static-protective surface. See the

Rack Installation Instructions

that comes with the server. If

the server is in tower form factor, lay the server on its side for easier operation.

3. Remove the server cover. See “Removing the server cover” on page 72.

4. Locate the backplanes. See “Hot-swap-drive backplane” on page 39.

5. Remove the AnyRAID adapter. See “Replacing the AnyRAID adapter” on page 159.

6. Remove all the installed hot-swap storage drives and dummy trays (if any) from the storage-drive bays.

See “Installing or replacing a hot-swap internal storage drive” on page 127.

7. Record the cable connections on the backplane, and then disconnect all the cables from the backplane.

8. Depending on the server model, do one of the following:

• For the server models with 3.5-inch-drive backplane, press the two release tabs

1

and gently lift the

3.5-inch-drive backplane a little bit upward so that it is released from the hooks on the chassis. Then,
carefully remove the 3.5-inch-drive backplane out of the chassis.

Figure 133. Removing the 3.5-inch-drive backplane

164

ThinkServer TD350 User Guide and Hardware Maintenance Manual

Содержание ThinkServer TD350



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ThinkServer TD350

Point Six Link Manager 4010-43 Manual preview
Link Manager 4010-43
Бренд: Point Six Страницы: 131
Hi-flying HF2221 User Manual preview
HF2221
Бренд: Hi-flying Страницы: 29
IBM iDataPlex dx320 6385 User Manual preview
iDataPlex dx320 6385
Бренд: IBM Страницы: 60
xFusion Digital Technologies FusionServer CH242 V5 Manual preview
FusionServer CH242 V5
Бренд: xFusion Digital Technologies Страницы: 61
IBM Netfinity 1000-8477 21Y Hardware Maintenance Manual preview
Netfinity 1000-8477 21Y
Бренд: IBM Страницы: 268
Buffalo BS-GS2008P Quick Setup Manual preview
BS-GS2008P
Бренд: Buffalo Страницы: 2
IBM 9009-41G Manual preview
9009-41G
Бренд: IBM Страницы: 36
xFusion Digital Technologies FusionServer G5500 V6 Manual preview
FusionServer G5500 V6
Бренд: xFusion Digital Technologies Страницы: 100
IBM totalstorage fastt100 Installation, User And Maintenance Manual preview
totalstorage fastt100
Бренд: IBM Страницы: 160
MAXDATA PLATINIUM 9000-4R User Manual preview
PLATINIUM 9000-4R
Бренд: MAXDATA Страницы: 18
H3C UniServer R4300 G6 User Manual preview
UniServer R4300 G6
Бренд: H3C Страницы: 542
SMART-AVI PresenterWall User Manual preview
PresenterWall
Бренд: SMART-AVI Страницы: 43
Supero SUPERSERVER 6113L-8 User Manual preview
SUPERSERVER 6113L-8
Бренд: Supero Страницы: 104
Supero SUPERSERVER 6017R-NTF User Manual preview
SUPERSERVER 6017R-NTF
Бренд: Supero Страницы: 126
Supero SuperServer 5017R-MF User Manual preview
SuperServer 5017R-MF
Бренд: Supero Страницы: 106
Supero SUPERSERVER 5015A-EHF User Manual preview
SUPERSERVER 5015A-EHF
Бренд: Supero Страницы: 106
Supero SuperServer 5013S-8 User Manual preview
SuperServer 5013S-8
Бренд: Supero Страницы: 110
Supero Supero SUPERSERVER 5015B-NT User Manual preview
Supero SUPERSERVER 5015B-NT
Бренд: Supero Страницы: 98

Бренды по названию

Популярные бренды

Загрузить еще бренды