Lenovo ThinkServer TD350 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 226

background image

Chapter 2. Server setup road map

This chapter provides a general road map to guide you through setting up your server.

The server setup procedure varies depending on the configuration of the server when it was delivered. In
some cases, the server is fully configured. Connect the server to the network and an ac power source, and
then you can turn on the server. In other cases, the server needs to have hardware devices installed, requires
hardware and firmware configuration, and requires an operating system to be installed.

The general procedure for setting up your server is:

1. Unpack the server package. See “Server package” on page 7.

2. Install any required hardware or server option. See the related topic in Chapter 6 “Replacing hardware”

3. Depending on the model, install the server into a standard rack cabinet by using the rail kit shipped

with the server. See

Rack Installation Instructions

that comes with your server. The rail kit and

Rack

Installation Instructions

are available on some models.

4. Connect the Ethernet cable and power cords to the server. See “Rear view of the server” on page

22 to locate the connectors.

5. Turn on the server to verify operation. See “Turning on the server” on page 55.

6. Review the Unified Extensible Firmware Interface (UEFI) Basic Input Output System (BIOS) settings and

customize as needed. See “Using the Setup Utility program” on page 57.

7. Configure RAID and install the operating system and basic drivers. See “Lenovo ThinkServer

Deployment Manager” on page 14 and “Configuring RAID” on page 65.

8. Install any additional drivers required for added features. Refer to the instructions that come with

the hardware option.

9. Configure Ethernet settings in the operating system by referring to the operating system help. This

step is not required if the operating system was installed using the Lenovo ThinkServer Deployment
Manager program.

10. Check for firmware and driver updates. See “Updating the firmware” on page 68.

11. Install management applications and any other applications. Refer to the documentation that comes

with the applications that you want to install.

© Copyright Lenovo 2014, 2016

5

«
...
17
18
19
20
21
...
»

Содержание ThinkServer TD350



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ThinkServer TD350

APSolute Vision

Бренд: Radware Страницы: 81

STRATOS S400-X44E

Бренд: Quanta Computer Страницы: 251

Netfinity 1000-8477 21Y

Бренд: IBM Страницы: 268

SUPERSERVER 6035B-8R+

Бренд: Supero Страницы: 110

UniServer R4900 G3

Бренд: H3C Страницы: 24

SuperServer E300-9A-4C

Бренд: Supermicro Страницы: 109

Бренд: DNP Страницы: 93

Бренд: Seyeon Страницы: 10

SuperServer E301-9D-8CN8TP

Бренд: Supermicro Страницы: 117

ProLiant DL100 G2 DPSS

Бренд: HP Страницы: 155

NetStorage 6000

Бренд: HP Страницы: 192

ProLiant DL100 G2 DPSS

Бренд: HP Страницы: 44

Бренд: Kramer Страницы: 2

Бренд: Planet Страницы: 71

Бренд: Redline Страницы: 50

Бренд: IBM Страницы: 136

Бренд: Godex Страницы: 31

Бренд: GRASS VALLEY Страницы: 108

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды