Lenovo ThinkServer TD350 Скачать руководство пользователя страница 171 | Manualshive

Страница: 171 / 226

Lenovo ThinkServer TD350 Скачать руководство пользователя страница 171

This topic applies only to server models that have a ThinkServer RAID Super Capacitor Module installed.
Depending on the model, the server might come with up to three ThinkServer RAID Super Capacitor Modules.

The ThinkServer RAID Super Capacitor Module protects the cache memory on the installed RAID card or
AnyRAID adapter. You can purchase a ThinkServer RAID Super Capacitor Module from the Lenovo Web site
at:
http://lenovoquickpick.com/usa/home/thinkserver/rack-and-tower-server

Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.

Notes:

• Depending on the model, your server might come with up to three ThinkServer RAID Super Capacitor

Modules.

• Use any documentation that comes with the ThinkServer RAID Super Capacitor Module and follow those

instructions in addition to the instructions in this topic.

To replace the ThinkServer RAID Super Capacitor Module, do the following:

1. Remove all external media from the drives and turn off all attached devices and the server. Then,

disconnect all power cords from electrical outlets and disconnect all cables that are connected to
the server.

2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,

clean, and static-protective surface. See the

Rack Installation Instructions

that comes with the server. If

the server is in tower form factor, lay the server on its side for easier operation.

3. Remove the server cover. See “Removing the server cover” on page 72.

4. Disconnect the cable from the ThinkServer RAID Super Capacitor Module. Remove the screw that

secures the ThinkServer RAID Super Capacitor Module and then disengage it from the chassis.

Figure 123. Removing the ThinkServer RAID Super Capacitor Module with the bracket from the chassis

Replacing hardware

157

«
...
169
170
171
172
173
...
»

Содержание ThinkServer TD350



































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды