Lenovo ThinkServer TD350 Скачать руководство пользователя страница 154

Страница: 154 / 226

7. Gently press the microprocessor retainer as shown to open it. Ensure that the small handles and the

microprocessor retainer are in the fully open position.

Note:

Do not drop anything onto the microprocessor socket while it is exposed. The socket pins must

be kept as clean as possible.

Figure 100. Opening the microprocessor retainer

8. Touch the static-protective package that contains the new microprocessor to any unpainted surface on

the outside of the server. Then, remove the new microprocessor from the package.

9. Remove the protective cover that protects the gold contacts on the bottom of the new microprocessor.

Do not touch the pins on the microprocessor socket and the gold contacts on the bottom of the new
microprocessor.

Figure 101. Do not touch the pins

140

ThinkServer TD350 User Guide and Hardware Maintenance Manual

Содержание ThinkServer TD350



































































































































































































































Результаты поиска

Содержание ThinkServer TD350

Отзывы:

Похожие инструкции для ThinkServer TD350

Бренды по названию

Популярные бренды

Lenovo ThinkServer TD350, Руководство пользователя и руководство по техническому обслуживанию аппаратного обеспечения

Результаты поиска

Содержание ThinkServer TD350

Отзывы:

Похожие инструкции для ThinkServer TD350

Бренды по названию

Популярные бренды