Lenovo ThinkServer TD350 Скачать руководство пользователя страница 118

Страница: 118 / 226

2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,

clean, and static-protective surface. See the

Rack Installation Instructions

that comes with the server. If

the server is in tower form factor, lay the server on its side for easier operation.

3. Remove the server cover. See “Removing the server cover” on page 72.

4. Locate the RAID upgrade key that you want to remove. Then, remove the RAID upgrade key from the

RAID 510i AnyRAID adapter or the RAID 520i PCIe adapter.

Note:

If necessary, remove the RAID 510i AnyRAID adapter or the RAID 520i PCIe adapter first for

easier operation. After you remove the upgrade key, reinstall the adapter. See “Replacing the AnyRAID
adapter” on page 159 or “Installing or removing a PCIe card” on page 90.

Figure 62. Removing the RAID 510i key

5. If you are instructed to return the old RAID upgrade key, follow all packaging instructions and use any

packaging materials that are supplied to you for shipping.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the removal procedure, go to “Completing the parts replacement” on page 180. Because

the hardware RAID 5 and 50 levels are not available without the RAID upgrade key, you might need to
reconfigure RAID for your server. For information about how to configure the hardware RAID, refer to the

MegaRAID SAS Software User Guide

on the documentation disc that comes with your server.

Installing or removing the Thunderbolt Memory Module

This topic applies only to RAID adapters that support the TMM. The following two types of TMM are available:

• ThinkServer RAID 720i Modular Flash

• ThinkServer RAID 720i Modular DRAM Upgrade

The TMM works as the cache memory for the following RAID adapters:

• RAID 720i AnyRAID Adapter

• RAID 720ix AnyRAID Adapter

• RAID 720i PCIe Adapter

You can purchase a TMM from Lenovo at:
http://lenovoquickpick.com/usa/home/thinkserver/rack-and-tower-server

104

ThinkServer TD350 User Guide and Hardware Maintenance Manual

Содержание ThinkServer TD350



































































































































































































































Результаты поиска

Содержание ThinkServer TD350

Отзывы:

Похожие инструкции для ThinkServer TD350

Бренды по названию

Популярные бренды

Lenovo ThinkServer TD350, Руководство пользователя и руководство по техническому обслуживанию аппаратного обеспечения

Результаты поиска

Содержание ThinkServer TD350

Отзывы:

Похожие инструкции для ThinkServer TD350

Бренды по названию

Популярные бренды