Lenovo ThinkServer TD350 Скачать руководство пользователя страница 26

Страница: 26 / 226

For more information about advanced system management, refer to the

ThinkServer System Manager

User Guide

, which is available for download at:

http://www.lenovo.com/UserManuals

Specifications

This topic lists the physical specifications for your server.

Dimensions

• For tower form factor

Width: 173 mm (6.81 inches)

Height: 459 mm (18.07 inches) with foot stands

Depth: 685 mm (26.97 inches) including the front door

• For rack form factor

Width: 482 mm (18.98 inches) with rack handles

Height: 173 mm (6.81 inches)

Depth: 664 mm (26.14 inches)

Weight

The product weight varies depending on different system configurations.

Range of product weight without package: 22 kg (48.5 lb) to 41.5 kg (91.49 lb)

Range of product weight with package: 26.57 kg (58.58 lb) to 46.07 kg (101.57 lb)

Electrical input

Universal input:

• Minimum:

90 V ac for 450-watt redundant power supplies compliant with 80 PLUS Gold

90 V ac for 550-watt, 750-watt, and 1100-watt redundant power supplies compliant with 80 PLUS
Platinum

180 V ac for 750-watt redundant power supplies compliant with 80 PLUS Titanium

• Maximum: 264 V ac

• Input frequency range: 47 Hz to 63 Hz

Environment

Your server complies with ASHRAE class A3 specifications. Depending on the hardware configuration, some
server models comply with ASHRAE class A4 or class A2 specifications.

• If your server meets the following hardware configuration requirements, your server complies with

ASHRAE class A4 specifications.

– Easy-swap-drive bays or eight 2.5-inch-drive bays

– CPU: Lenovo-qualified; a maximum of 120-W thermal design power; not low-power type (no L-suffix in

the CPU name)

– Do not have internal tape drives installed

– Two power supplies installed for redundancy

ThinkServer TD350 User Guide and Hardware Maintenance Manual

Содержание ThinkServer TD350



































































































































































































































Результаты поиска

Содержание ThinkServer TD350

Отзывы:

Бренды по названию

Популярные бренды

Lenovo ThinkServer TD350, Руководство пользователя и руководство по техническому обслуживанию аппаратного обеспечения

Результаты поиска

Содержание ThinkServer TD350

Отзывы:

Бренды по названию

Популярные бренды