Lenovo ThinkServer TD350 Скачать руководство пользователя страница 186 | Manualshive

Страница: 186 / 226

background image

Replacing the coin-cell battery

Attention:

Do not open your server or attempt any repair before reading and understanding “Read this first: safety

information” on page iii and “Guidelines” on page 69.

Your server has a special type of memory that maintains the date, time, and configuration information for
built-in features. The coin-cell battery keeps the information active when you turn off the server. The
coin-cell battery normally requires no charging nor maintenance throughout its life; however, no battery lasts
forever. If the coin-cell battery fails, the date, time, and configuration information, including passwords, are
lost and an error message is displayed when you turn on the server.

DANGER

Danger of explosion if battery is incorrectly replaced.

When replacing the lithium coin-cell battery, use only the same or an equivalent type that is
recommended by the manufacturer. The battery contains lithium and can explode if not properly
used, handled, or disposed of.

Do not:

• Throw or immerse into water

• Heat to more than 100°C (212°F)

• Repair or disassemble

Dispose of the battery as required by local ordinances or regulations.

The following statement applies to users in the state of California, U.S.A.

California Perchlorate Information:

Products containing manganese dioxide lithium coin cell batteries may contain perchlorate.

Perchlorate Material - special handling may apply, See
http://www.dtsc.ca.gov/hazardouswaste/perchlorate

Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.

To replace the coin-cell battery, do the following:

Note:

After you replace the coin-cell battery, you must reset passwords, reset system date and time, and

reconfigure the server.

1. Remove all external media from the drives and turn off all attached devices and the server. Then,

disconnect all power cords from electrical outlets and disconnect all cables that are connected to
the server.

2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,

clean, and static-protective surface. See the

Rack Installation Instructions

that comes with the server. If

the server is in tower form factor, lay the server on its side for easier operation.

3. Remove the server cover. See “Removing the server cover” on page 72.

4. Remove the cooling shroud. See “Removing the cooling shroud” on page 75.

5. Locate the coin-cell battery. See “Server components” on page 25.

172

ThinkServer TD350 User Guide and Hardware Maintenance Manual

«
...
184
185
186
187
188
...
»

Содержание ThinkServer TD350



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ThinkServer TD350

Бренд: Aastra Страницы: 592

eserver pSeries 690

Бренд: IBM Страницы: 142

eServer 370 xSeries

Бренд: IBM Страницы: 218

BladeCenter PS703

Бренд: IBM Страницы: 298

BladeCenter T Type 8720

Бренд: IBM Страницы: 180

Бренд: Xerox Страницы: 8

Бренд: HYVE Страницы: 22

Бренд: Sun Microsystems Страницы: 90

Snap! Server 4000

Бренд: Quantum Страницы: 8

BACnet/IP Server-SUNWAYS

Бренд: IntesisBox Страницы: 5

Бренд: Digital Equipment Страницы: 15

BladeCenter HS20 Type 8843

Бренд: IBM Страницы: 112

Бренд: Vxl Страницы: 2

UniServer R2700 G3

Бренд: H3C Страницы: 226

SMAVIA DMS 2400 II

Бренд: dallmeier Страницы: 36

Бренд: Data-Tronix Страницы: 29

Бренд: Data-Tronix Страницы: 30

376227-B21 - ProLiant InfiniBand 4x Fabric Copper Switch

Бренд: HP Страницы: 169

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды