Lenovo ThinkServer TD350 Скачать руководство пользователя страница 168

Страница: 168 / 226

11. Save the removed dummy storage-drive tray in the event that you later remove the 2.5-inch drive

and need a dummy tray to cover the drive bay.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To configure RAID, go to “Configuring RAID” on page 65.

Replacing the front-panel board

Attention:

Do not open your server or attempt any repair before reading and understanding “Read this first: safety

information” on page iii and “Guidelines” on page 69.

Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.

Notes:

• Depending on the model, your server might look slightly different from the illustrations in this topic.

• Use any documentation that comes with the new front-panel board and follow those instructions in

addition to the instructions in this topic.

• The front-panel board is sensitive to ESD. Ensure that you read and understand “Handling static-sensitive

devices” on page 70 first and carefully perform the operation.

To replace the front-panel board, do the following:

1. Remove all external media from the drives and turn off all attached devices and the server. Then,

disconnect all power cords from electrical outlets and disconnect all cables that are connected to
the server.

2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,

clean, and static-protective surface. See the

Rack Installation Instructions

that comes with the server.

3. Remove the server cover. See “Removing the server cover” on page 72.

4. Remove the front bezel. See “Removing and reinstalling the front bezel” on page 76.

5. Locate the front panel. See “Front panel” on page 20.

6. Disconnect the front-panel cable from the rear of the front-panel board and from the front panel

connector on the system board. See “System board components” on page 47.

7. If necessary, remove any parts and disconnect any cables that might impede your access to the front

panel cable. Record the cable routing, and then release the front panel cable from any cable clips
or ties in the chassis.

154

ThinkServer TD350 User Guide and Hardware Maintenance Manual

Содержание ThinkServer TD350



































































































































































































































Результаты поиска

Содержание ThinkServer TD350

Отзывы:

Бренды по названию

Популярные бренды

Lenovo ThinkServer TD350, Руководство пользователя и руководство по техническому обслуживанию аппаратного обеспечения

Результаты поиска

Содержание ThinkServer TD350

Отзывы:

Бренды по названию

Популярные бренды