Lenovo ThinkServer TD350 Скачать руководство пользователя страница 163

Страница: 163 / 226

b. Disconnect the power cord from the failing hot-swap redundant power supply. Then, press the

release tab

and pull the handle

at the same time to slide the failing hot-swap redundant

power supply out of the chassis.

Figure 113. Removing a hot-swap redundant power supply

2. Touch the static-protective package that contains the new hot-swap redundant power supply to any

unpainted surface on the outside of the server. Then, remove the new hot-swap redundant power
supply from the package.

3. Note the orientation of the new hot-swap redundant power supply, and then slide it into the chassis until

it snaps into position.

Figure 114. Installing a hot-swap redundant power supply

4. Connect the power cord to the power cord connector on the new power supply. Then, check the

status LEDs near the power cord connector. For information about the status LEDs, see “Power supply
status LEDs” on page 32.

Chapter 6

Replacing hardware

149

Содержание ThinkServer TD350



































































































































































































































Результаты поиска

Содержание ThinkServer TD350

Отзывы:

Похожие инструкции для ThinkServer TD350

Бренды по названию

Популярные бренды

Lenovo ThinkServer TD350, Руководство пользователя и руководство по техническому обслуживанию аппаратного обеспечения

Результаты поиска

Содержание ThinkServer TD350

Отзывы:

Похожие инструкции для ThinkServer TD350

Бренды по названию

Популярные бренды