Lenovo ThinkServer TD350 Скачать руководство пользователя страница 152 | Manualshive

Страница: 152 / 226

background image

7. Connect the power and signal cable

1

to the rear of the tape drive.

Figure 98. Connecting the power and signal cable to the rear of the tape drive

8. Do one of the following:

• If you are installing a tape drive, save the removed protective shield in case that you later remove

the drive and need the protective shield to cover the drive bay.

• If you are replacing a tape drive and are instructed to return the old tape drive, follow all packaging

instructions. Then, use any packaging materials that are supplied to you for shipping.

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 180.

Installing or replacing the microprocessor

This topic contains the following items:

•

“Installing the second microprocessor” on page 138

•

“Replacing the microprocessor” on page 142

Installing the second microprocessor

Attention:

Do not open your server or attempt any repair before reading and understanding “Read this first: safety

information” on page iii and “Guidelines” on page 69.

Depending on the model, your server might come with one or two microprocessors. For server models with
one microprocessor, the microprocessor is installed in the microprocessor socket 1 and the microprocessor
socket 2 is protected by a plastic socket cover. You can purchase a microprocessor option kit from Lenovo
and install the second microprocessor to expand system capabilities.

CAUTION:

Turn off the server and wait several minutes to let the server cool before removing the server cover.

138

ThinkServer TD350 User Guide and Hardware Maintenance Manual

«
...
150
151
152
153
154
...
»

Содержание ThinkServer TD350



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ThinkServer TD350

Бренд: Yeong Yang Страницы: 7

Бренд: Devolinx Страницы: 51

Бренд: Vecow Страницы: 122

Бренд: Buffalo Страницы: 2

WECS II 2048/DMX/02

Бренд: Oase Страницы: 67

H SERIES RS/6000

Бренд: IBM Страницы: 424

Бренд: IBM Страницы: 16

ProtectServer External 2

Бренд: SafeNet Страницы: 22

Бренд: MSI Страницы: 54

Бренд: IBM Страницы: 48

Бренд: t.a.c. Страницы: 36

Бренд: MSI Страницы: 18

Бренд: Lenovo Страницы: 186

42U 1200 mm Deep Dynamic Rack

Бренд: Lenovo Страницы: 42

Бренд: Lenovo Страницы: 32

30131AU - IdeaCentre D400 - 3013

Бренд: Lenovo Страницы: 65

Бренд: Lenovo Страницы: 176

Бренд: Lenovo Страницы: 90

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды