Lenovo ThinkServer TD350 Скачать руководство пользователя страница 155

Страница: 155 / 226

10. Note the orientation of the new microprocessor. Hold the new microprocessor by its edges and align

the notches

on it with the tabs

in the microprocessor socket. Then, carefully lower the new

microprocessor straight down into the microprocessor socket.

Note:

The small triangle

on one corner of the new microprocessor is the microprocessor orientation

indicator. The new microprocessor is in the correct orientation when this indicator faces the beveled
corner

of the microprocessor socket.

Figure 102. Installing the microprocessor

11. Remove the plastic microprocessor socket cover. Store the microprocessor socket cover in the event

that you later remove the microprocessor and need the socket cover to protect the pins on the socket.

Note:

Do not remove the socket cover until you install a microprocessor into the socket. If you remove

the microprocessor, install the socket cover or a new microprocessor in the first place.

Figure 103. Removing the microprocessor socket cover

Chapter 6

Replacing hardware

141

Содержание ThinkServer TD350



































































































































































































































Результаты поиска

Содержание ThinkServer TD350

Отзывы:

Бренды по названию

Популярные бренды

Lenovo ThinkServer TD350, Руководство пользователя и руководство по техническому обслуживанию аппаратного обеспечения

Результаты поиска

Содержание ThinkServer TD350

Отзывы:

Бренды по названию

Популярные бренды