Lenovo ThinkServer TD350 Скачать руководство пользователя страница 126

Страница: 126 / 226

6. Locate the TPM connector on the system board. Insert the TPM into the TPM connector.

Figure 67. Installing the TPM

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation, go to “Completing the parts replacement” on page 180. Then, you can

configure the TPM function in the Setup Utility program. See “Configuring the TPM function” on page 62.

Removing the TPM

Attention:

Do not open your server or attempt any repair before reading and understanding “Read this first: safety

information” on page iii and “Guidelines” on page 69.

Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.

112

ThinkServer TD350 User Guide and Hardware Maintenance Manual

Содержание ThinkServer TD350



































































































































































































































Результаты поиска

Содержание ThinkServer TD350

Отзывы:

Похожие инструкции для ThinkServer TD350

Бренды по названию

Популярные бренды

Lenovo ThinkServer TD350, Руководство пользователя и руководство по техническому обслуживанию аппаратного обеспечения

Результаты поиска

Содержание ThinkServer TD350

Отзывы:

Похожие инструкции для ThinkServer TD350

Бренды по названию

Популярные бренды