Lenovo ThinkServer TD350 Скачать руководство пользователя страница 110

Страница: 110 / 226

To install the SD module, do the following:

1. Remove all external media from the drives and turn off all attached devices and the server. Then,

disconnect all power cords from electrical outlets and disconnect all cables that are connected to
the server.

2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,

clean, and static-protective surface. See the

Rack Installation Instructions

that comes with the server. If

the server is in tower form factor, lay the server on its side for easier operation.

3. Remove the server cover. See “Removing the server cover” on page 72.

4. Remove the cooling shroud. See “Removing the cooling shroud” on page 75.

5. Remove any parts and disconnect any cables that might impede your operation.

6. Locate the SD-module connector on the system board. See “System board components” on page 47.

7. Touch the static-protective package that contains the SD module to any unpainted surface on the

outside of the server. Then, take the SD module out of the package.

8. Insert the SD card into the SD card slot. The card might stop before it is completely installed into the SD

module. Ensure that you insert the card firmly until you hear a click.

9. Ensure that the two holes in the SD module are aligned with the two plastic pins on the system board.

Then, lower the SD module straight down until it is securely seated.

Figure 57. Installing the SD module

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation, go to “Completing the parts replacement” on page 180.

Removing the SD module

Attention:

Do not open your server or attempt any repair before reading and understanding “Read this first: safety

information” on page iii and “Guidelines” on page 69.

Before you begin, print all the related instructions or ensure that you can view the PDF version on another
computer for reference.

Note:

Use any documentation that comes with the SD module and follow those instructions in addition to

the instructions in this topic.

ThinkServer TD350 User Guide and Hardware Maintenance Manual

Содержание ThinkServer TD350



































































































































































































































Результаты поиска

Содержание ThinkServer TD350

Отзывы:

Похожие инструкции для ThinkServer TD350

Бренды по названию

Популярные бренды

Lenovo ThinkServer TD350, Руководство пользователя и руководство по техническому обслуживанию аппаратного обеспечения

Результаты поиска

Содержание ThinkServer TD350

Отзывы:

Похожие инструкции для ThinkServer TD350

Бренды по названию

Популярные бренды