Lenovo ThinkServer TD350 Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 226

background image

PCIe interposer card

The PCIe interposer card is used in server models that support up to thirty-two 2.5-inch hot-swap drives.
You can purchase a supported PCIe interposer card from Lenovo and install it into the server. For a list of
ThinkServer options, go to:
http://lenovoquickpick.com/usa/home/thinkserver/rack-and-tower-server

Note:

The option kit is designed for different types of servers and might contain additional cables that are

not required for your server.

The following illustration shows the connectors on the PCIe interposer card.

Figure 19. PCIe interposer card

1

PCIe connector

Used to connect to the PCI-E 0 and PCI-E 1 connectors on the Lenovo ThinkServer RAID 720ix AnyRAID
Adapter.

2

I2C connector

Used to connect to the I2C connector on the system board.

Hot-swap-drive backplane

Your server comes with one of the following drive bay and backplane configurations:

• Five 3.5-inch-drive bays with one backplane

• Fifteen 3.5-inch-drive bays with one backplane

• Eight 2.5-inch-drive bays with one backplane

• Sixteen 2.5-inch-drive bays with two backplanes

• Thirty-two 2.5-inch-drive bays with four backplanes

Product overview

39

«
...
51
52
53
54
55
...
»

Содержание ThinkServer TD350



































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ThinkServer TD350

Бренд: i3 International Страницы: 2

Бренд: Axis Страницы: 66

Бренд: ASROCK Rack Страницы: 51

callpilot 1002rp

Бренд: Avaya Страницы: 150

ApplianceStor 75

Бренд: Rasilient Страницы: 24

Бренд: Thecus Страницы: 102

LAN Brick Eth 10

Бренд: MPI Technologies Страницы: 2

Бренд: Advantech Страницы: 76

Бренд: Advantech Страницы: 92

Бренд: SCT Страницы: 33

AcquiLite A7810

Бренд: Obvius Страницы: 29

Бренд: Measy Страницы: 15

Бренд: Lantronix Страницы: 223

Бренд: Optibase Страницы: 28

Бренд: QUANTA Страницы: 36

Бренд: Oracle Страницы: 6

SPARC Enterprise M4000

Бренд: Oracle Страницы: 78

Бренд: FieldServer Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды