Lenovo ThinkServer TD350 Скачать руководство пользователя страница 149

Страница: 149 / 226

9. Align the holes in the drive tray with the corresponding ones on the new easy-swap drive. Then, install

the four screws to secure the drive to the drive tray.

Figure 93. Installing the drive to the drive tray

10. Slide the new easy-swap drive into the drive bay from the front until it snaps into position, and then

close the handle.

Figure 94. Installing the easy-swap drive

11. Close the front door (if available).

12. Do one of the following:

• If you are installing an easy-swap drive, save the removed dummy tray in case that you later remove

the easy-swap drive and need a dummy tray to cover the drive bay.

• If you are replacing an easy-swap drive and are instructed to return the old easy-swap drive, follow all

packaging instructions and use any packaging materials that are supplied to you for shipping.

Chapter 6

Replacing hardware

135

Содержание ThinkServer TD350



































































































































































































































Результаты поиска

Содержание ThinkServer TD350

Отзывы:

Похожие инструкции для ThinkServer TD350

Бренды по названию

Популярные бренды

Lenovo ThinkServer TD350, Руководство пользователя и руководство по техническому обслуживанию аппаратного обеспечения

Результаты поиска

Содержание ThinkServer TD350

Отзывы:

Похожие инструкции для ThinkServer TD350

Бренды по названию

Популярные бренды