Lenovo ThinkServer TD350 Скачать руководство пользователя страница 114

Страница: 114 / 226

Notes:

• If you remove the RAID 110i upgrade key, the onboard SATA software RAID 5 will be unavailable.

• Use any documentation that comes with the RAID 110i upgrade key and follow those instructions in

addition to the instructions in this topic.

If your server has a RAID 110i upgrade key installed, do the following when you want to remove the RAID
110i upgrade key:

Attention:

Removing the RAID 110i upgrade key might impact your RAID configurations. Back up your data

before you begin to avoid any data loss due to a RAID configuration change.

1. Remove all external media from the drives and turn off all attached devices and the server. Then,

disconnect all power cords from electrical outlets and disconnect all cables that are connected to
the server.

2. If the server is installed in a rack cabinet, remove the server from the rack cabinet and place it on a flat,

clean, and static-protective surface. See the

Rack Installation Instructions

that comes with the server. If

the server is in tower form factor, lay the server on its side for easier operation.

3. Remove the server cover. See “Removing the server cover” on page 72.

4. Remove the cooling shroud. See “Removing the cooling shroud” on page 75.

100

ThinkServer TD350 User Guide and Hardware Maintenance Manual

Содержание ThinkServer TD350



































































































































































































































Результаты поиска

Содержание ThinkServer TD350

Отзывы:

Похожие инструкции для ThinkServer TD350

Бренды по названию

Популярные бренды

Lenovo ThinkServer TD350, Руководство пользователя и руководство по техническому обслуживанию аппаратного обеспечения

Результаты поиска

Содержание ThinkServer TD350

Отзывы:

Похожие инструкции для ThinkServer TD350

Бренды по названию

Популярные бренды