Lenovo ThinkServer TD350 Скачать руководство пользователя страница 193 | Manualshive

Страница: 193 / 226

Lenovo ThinkServer TD350 Скачать руководство пользователя страница 193

8. Lift the release button

1

and then disengaged the power interface board from the chassis.

Note:

Carefully handle the power interface board by its edges.

Figure 148. Removing the power interface board

9. Place the old power interface board on a clean, flat, and static-protective surface. Touch the

static-protective package that contains the new power interface board to any unpainted surface on the
outside of the server. Then, take the new power interface board out of the package.

10. Install the new power interface board into the chassis. Align the two holes in the new power interface

board with the corresponding mounting stubs on the chassis. Then, move the power interface board
towards the front of the server until the power interface board snaps into position.

Figure 149. Installing the power interface board

11. Install all parts that you have removed and reconnect all cables. Refer to the information that you have

recorded and the related topics in Chapter 6 “Replacing hardware” on page 69.

12. If you are instructed to return the old power interface board, follow all packaging instructions and use

any packaging materials that are supplied to you for shipping.

Replacing hardware

179

«
...
191
192
193
194
195
...
»

Содержание ThinkServer TD350



































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды