Komatsu WA380-8 Скачать руководство пользователя | Manualshive

Страница: 165 / 432

background image

The room lamp switch illuminates the room lamp.
Position (A): OFF (goes out)
Position (B): Lights up when cab door opens.
Position (C): ON (lights up)

REMARK

• The room lamp lights up even when the starting switch is

at OFF position. When leaving the operator's seat, set to
position (A) or (B).

• When operating the machine with the cab door fully

opened, set the switch to position (A).

BEACON LAMP SWITCH

(if equipped)
The beacon lamp switch is used to turn on or off the beacon
lamp.
Position (A): ON
Position (B): OFF

REAR WORKING LAMP SWITCH

k

k

WARNING

The working lamps must be turned off when the machine is traveling on a public road.

Use the rear working lamp switch to light up the rear working
lamps.
Position (A): The working lamps light up.
Position (B): The working lamps go out.
When position (A) is pressed, the pilot lamp lights up, and the
working lamps turn ON.

ECSS SWITCH

k

k

WARNING

• If the ECSS switch is turned ON during travel or with the work equipment raised, the machine starts

moving instantly. Take care.

• If the machine is operated with the ECSS switch ON, the work equipment may starts moving at the

moment when the ECSS is actuated. Take care.

• Never turn ECSS switch ON during inspection or maintenance. The work equipment will move and it

is dangerous.

OPERATION

EXPLANATION OF COMPONENTS

3-101

«
...
163
164
165
166
167
...
»

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WA380-8

Бренд: Vestil Страницы: 17

Wacker Neuson SM325-27T

Бренд: DINGO Страницы: 20

Бренд: Takeuchi Страницы: 239

Бренд: Takeuchi Страницы: 10

Бренд: Takeuchi Страницы: 194

Бренд: Takeuchi Страницы: 235

PalletPal Spring

Бренд: Southworth Страницы: 16

Бренд: Grizzly Страницы: 15

Бренд: RHINO Страницы: 104

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды