manualshive.com logo in svg

Komatsu WA380-8, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Komatsu WA380-8 Скачать руководство пользователя страница 227

REMARK

If drain plug (2) is heavy to operate, apply grease to O-ring (6) of plug (2) according to the following proce-
dure.
1) Place  a  container  under  drain  hose  (4)  to  catch  the

drained fuel.

2) Loosen  plug  (2)  and  drain  all  the  fuel  and  sediment

through drain hose (4).

3) Check  that  nothing  more  comes  out  from  drain  hose

(4), then remove plug (2).

4) Apply a suitable amount of grease to O-ring (6). At this

time, take care that grease will not stick to water drain
port (a) and threaded portion of the plug.

5) Tighten plug (2) by hand until it stops.
6) Remove the container for catching the drained fuel.

• If transparent cup (3) is so dirty that the inside cannot be seen, clean it when replacing the filter.
• When  the  plug  (2)  has  been  removed  during  the  cleaning  work,  apply  grease  to  O-ring  (6)  and

tighten with your finger until it stops.

METHOD FOR CHECKING COOLANT LEVEL, ADDING COOLANT

k

k

 WARNING

• Do not open the radiator cap unless necessary. When checking the coolant level, check the reser-

voir tank when the engine is cold.

• Immediately after the engine is stopped, the coolant is at high temperature. And the pressure is still

accumulated in the radiator. If the cap is removed in this condition, it is dangerous that you may get
burn injury. Always wait for the temperature to go down, and turn the cap slowly to release the pres-
sure.

 

k

k

 CAUTION

When refilling with coolant, support your body securely by using the steps and handrails provided.
 

1.

Open platform cover (1) on the right side of the machine.

OPERATION

MACHINE OPERATIONS AND CONTROLS

3-163

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды