Komatsu WA380-8 Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 432

Komatsu WA380-8 Скачать руководство пользователя страница 84

TORQUE CONVERTER OIL TEMPERATURE CAUTION LAMP

The torque converter oil temperature caution lamp warns about
overheating of the torque converter oil.
If  the  torque  converter  oil  temperature  is  abnormally  high,  the
lamp lights up in red and action level “L02” is displayed. At the
same  time,  the  centralized  warning  lamp  lights  up  and  alarm
buzzer sounds intermittently.
Place the machine in a safe place, set the directional lever and
directional  selector  switch  (if  equipped)  to  NEUTRAL  position
(N), and run the engine at a medium speed under no load until
the lamp goes out.

HYDRAULIC OIL TEMPERATURE CAUTION LAMP

The  hydraulic  oil  temperature  caution  lamp  warns  about  over-
heating of the hydraulic oil.
If  the  hydraulic  oil  temperature  is  abnormally  high,  the  lamp
lights up in red and action level “L02” is displayed. At the same
time, the centralized warning lamp lights up and alarm buzzer
sounds intermittently.
Place the machine in a safe place, set the directional lever and
directional  selector  switch  (if  equipped)  to  NEUTRAL  position
(N), and run the engine at a medium speed under no load until
the lamp goes out.

FUEL LEVEL CAUTION LAMP

The fuel level caution lamp warns about low remaining fuel lev-
el.
The lamp lights up in red if the fuel level is 28 ℓ or below.
Add fuel as soon as possible.

BRAKE OIL PRESSURE CAUTION LAMP

The brake oil pressure caution lamp warns that the brake oil
pressure is below the specified value.

• When action level “L03” is displayed

If  the  brake  oil  pressure  drops  below  the  specified  value
while  the  engine  is  running,  the  lamp  lights  up  in  red.  At
the same time, the centralized warning lamp lights up and
alarm buzzer sounds intermittently.
Stop  the  operation,  move  the  machine  to  a  safe  place,
stop the engine, then ask your Komatsu distributor for in-
spection and maintenance.

• When action level is not displayed and lamp lights up in

red
If the brake oil pressure is below the specified value while the engine is stopped, the lamp lights up in red.
When the engine is started, the lamp lights up in red until the brake oil pressure increases above the speci-
fied value. At the same time, the centralized warning lamp lights up and alarm buzzer sounds intermittently.
Wait until the lamp goes out, and then move the machine.

EXPLANATION OF COMPONENTS

OPERATION

3-20

«
...
82
83
84
85
86
...
»

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды