Komatsu WA380-8 Скачать руководство пользователя | Manualshive

Страница: 407 / 432

background image

Continuous mode

When  switch  is  operated  to  the  limit  of  position  (C),  the  set
maximum  flow  is  held  and  the  third  attachment  continues  the
operation even if the switch operation is stopped. This action is
called the detent control.
Use this control when the installed attachment requires contin-
uous hydraulic oil flow.
Detent control operation pilot lamp (D) lights up during the de-
tent control.
The  detent  control  is  canceled  by  any  of  the  following  opera-
tions.

• Operate the switch again.
• Turn the work equipment lock switch ON.
• Turn the starting switch key to OFF position.
• Stop the engine.
• Cancel the continuous mode on the monitor.

Proportional mode

This mode does not have the detent control function which the continuous mode has.

REMARK

The hydraulic oil discharged volume is in proportion to the stroke of the switch in both continuous mode and
proportional mode.

LCD UNIT

(1) Flow control mode pilot lamp (Continuous mode/Proportion-

al mode)

(2) Detent operation pilot lamp
(3) Attachment oil flow level

OIL FLOW CONTROL MODE PILOT LAMP (FIXED OIL FLOW MODE)

The flow control mode pilot lamp (continuous mode) lights up
when the flow control of PCS is in the continuous mode.

ATTACHMENTS AND OPTIONS

HANDLE MULTIFUNCTION MONO-LEVER

6-7

«
...
405
406
407
408
409
...
»

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WA380-8

Бренд: Terex Страницы: 85

Бренд: Hyundai Страницы: 262

Бренд: Takeuchi Страницы: 312

Бренд: jcb Страницы: 18

Бренд: Woody Страницы: 28

Бренд: Komatsu Страницы: 41

Бренд: Komatsu Страницы: 284

Бренд: Doosan Страницы: 60

Бренд: Doosan Страницы: 210

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды