Komatsu WA380-8 Скачать руководство пользователя | Manualshive

Страница: 51 / 432

background image

• When leaving the machine, lock the work equipment by

pressing work equipment lock switch (1) (pilot lamp lights
up) and set parking brake switch (2) to ON (operation) po-
sition (A), then stop the engine.

• Always close the operator's cab door, and use the key to

lock all the equipment in order to prevent any unauthorized
person from operating the machine. Always remove the
key, take it with you, and keep it in the specified place.

• If it is necessary to park the machine on a slope, set

blocks under the tires to prevent the machine from moving.

PRECAUTIONS FOR TRANSPORTATION

When the machine is transported on a trailer, serious personal injury or death may result because of the acci-
dent during transportation. Always observe the following.

• Always check the machine dimensions carefully. Depending on the work equipment installed, the machine

weight, transportation height, and overall length differ.

• Check beforehand that all bridges and other structures on the transportation route are strong enough to

withstand the combined weight of the transporter and the machine being transported.

• This machine needs to be divided into components for transportation depending on the regulation. When

transporting the machine, consult your Komatsu distributor.

• Lock the frame with the frame lock bar to prevent the machine from articulating.
• Fit chains to the front frame and the rear frame to hold the machine securely in position.
• For details of the transportation procedure, see “TRANSPORTATION (3-234)”.

PRECAUTIONS WHEN LOADING AND UNLOADING

If handling is improper when loading or unloading the machine, it is dangerous that the machine may tip over or
fall. It requires particular attention. Always observe the following.

• Perform loading and unloading on a firm, level ground only. Avoid road edge or place near the cliff.

SAFETY

PRECAUTIONS FOR OPERATION

2-31

«
...
49
50
51
52
53
...
»

Содержание WA380-8

















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WA380-8

FORKLIFT 5FD 7 0-30 Series

Бренд: Toyota Страницы: 71

Бренд: Eurotrac Страницы: 72

Бренд: jcb Страницы: 31

Бренд: Doosan Страницы: 210

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды